American Standard 9205.024.339 Manuel D’Utilisation
- 3 -
7 7 0 0 1 5 - 1 0 0
Care and Cleaning of Vanity
Clean the product by using soft, slightly damp cloth. Buff the product by using
a soft dry cloth. Avoid using silicone cleaners and waxes.
Clean up excess water and spills immediately. Use a blotting rather than a
wiping action. Water left over a long period of time will cause white spots in
the finish.
NOTE: Please note that some chemicals may damage the finish. Take care
to avoid the following: iodine, hair dye, after shave lotion, shaving cream,
alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray
Disinfectant®, Dow Disinfectant®, acetone, paint remover, Formula 409®,
Tile-X®, and Nair®.
a soft dry cloth. Avoid using silicone cleaners and waxes.
Clean up excess water and spills immediately. Use a blotting rather than a
wiping action. Water left over a long period of time will cause white spots in
the finish.
NOTE: Please note that some chemicals may damage the finish. Take care
to avoid the following: iodine, hair dye, after shave lotion, shaving cream,
alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray
Disinfectant®, Dow Disinfectant®, acetone, paint remover, Formula 409®,
Tile-X®, and Nair®.
Care and Cleaning of the Marble Vanity Top
Marble is porous and easily stained. Wipe off anything spilled on it
immediately. It should be washed or cleaned regularly with fresh warm water
and a non-abrasive clean cloth. Also, using a non-abrasive, neutral (pH
balanced) cleaner will help remove dirt and grime, but it is recommended to
first try warm water only.
Marble should be sealed regularly with a good quality marble sealer. Marble
sealers are available at most retail home supply stores. Follow the
instructions on the sealer container for proper application and frequency of
use. The sealer acts as a stain inhibitor and prevents most stains and soil
from being absorbed into the porous surface, but it is NOT a guarantee
against staining. All spills should be cleaned immediately. Avoid contact with
all oils and petroleum-based products. Also, avoid contact with all acid or
caustic products such as vinegar, citrus or fruit juices, soda, chlorine, and nail
polish remover. If the marble is well sealed, the warm water and non-abrasive
cloth should keep it clean.
immediately. It should be washed or cleaned regularly with fresh warm water
and a non-abrasive clean cloth. Also, using a non-abrasive, neutral (pH
balanced) cleaner will help remove dirt and grime, but it is recommended to
first try warm water only.
Marble should be sealed regularly with a good quality marble sealer. Marble
sealers are available at most retail home supply stores. Follow the
instructions on the sealer container for proper application and frequency of
use. The sealer acts as a stain inhibitor and prevents most stains and soil
from being absorbed into the porous surface, but it is NOT a guarantee
against staining. All spills should be cleaned immediately. Avoid contact with
all oils and petroleum-based products. Also, avoid contact with all acid or
caustic products such as vinegar, citrus or fruit juices, soda, chlorine, and nail
polish remover. If the marble is well sealed, the warm water and non-abrasive
cloth should keep it clean.
1
2
WASHER
LOCKNUT
TAILPIECE
SINK
GRID
DRAIN
BODY
RUBBER
GASKET
CUTOUT
RISER
COUNTER
SURFACE
(TYPICAL)
(TYPICAL)
“O” RING
Optional Laminate Marble Top Installation
NOTE: Tops are precut to accommodate recommended sinks and faucet.
OPTION 1:
Glass Vessel or Round China Vessel
Glass Vessel or Round China Vessel
OPTION 2:
China Rectangular Sink – Refer to instructions
supplied with rectangular vessel.
China Rectangular Sink – Refer to instructions
supplied with rectangular vessel.
Place the riser (“O” Ring side down) over the hole in countertop
surface. Position Glass Vessel onto riser aligning holes.
surface. Position Glass Vessel onto riser aligning holes.
The sink is mounted and secured on the countertop by the grid
drain assembly, which is installed as follows:
drain assembly, which is installed as follows:
1. Place the rubber gasket beneath the rim of the grid
drain body and insert drain through sink and riser.
2. Install the washer and locknut onto the grid drain from
beneath the countertop surface. Hand tighten.
3. Level sink front-to-back and side-to-side, then tighten
(do not overtighten).
4. Install tail piece.
drain body and insert drain through sink and riser.
2. Install the washer and locknut onto the grid drain from
beneath the countertop surface. Hand tighten.
3. Level sink front-to-back and side-to-side, then tighten
(do not overtighten).
4. Install tail piece.
3
4
Apply a bead of silicon adhesive to the rim of the vanity. Place
the marble top centered left to right on the vanity and with the
back edge of the top even with the rear of the vanity. Clean up
any excess silicon.
the marble top centered left to right on the vanity and with the
back edge of the top even with the rear of the vanity. Clean up
any excess silicon.
Install faucet and connect to supply in accordance with the
manufacturer’s instructions.
manufacturer’s instructions.
Connect the trap to the
drain assembly and hand
tighten to check
alignment. It may be
necessary to cut off part of
the tail piece (area “B”) or
part of the horizontal leg
of the trap (area “C”).
drain assembly and hand
tighten to check
alignment. It may be
necessary to cut off part of
the tail piece (area “B”) or
part of the horizontal leg
of the trap (area “C”).
5
Water test unit, check for leakage and correct as needed.
6
B
C
Laminate Marble Top w/
Glass Vessel or
China Round Vessel
Glass Vessel or
China Round Vessel
Diagram of OPTION 2
Diagram of OPTION 1
Rectangular Vessel Sink
on Studio Vanity
on Studio Vanity