TEAC AG20D Manuel D’Utilisation

SPEAKER CONFIGURATION, DELAY TIME & DYNAMIC RANGE CONTROL

SPEAKER CONFIGURATION
It is important to configure your speakers correctly in
order to get the most from your AV Receiver. This
versatile AV Receiver provides the flexibility to
experience multi-channel surround sound without a
center speaker. However, for best results with Dolby
Pro Logic II, DTS and Dolby Digital decoding, at
least 5 speakers (Left, Center, Right, Left Rear and
Right Rear) should be used. (Note: As with all
surround sound configurations, we recommend the
use of a Subwoofer speaker to fully experience the
Low Frequency Effect encoded into most of today's
DVD movies).

BASS MODE
There are 2 preset speaker configurations based on
the size of your speakers.
Default is Mode 1.

Front

& R

Center Rear L

& R

Sub-Woofer

Mode1 Small Small Small On
Mode2 Large Small Small On

Press BASS MODE to select one of the 2 modes
according to your speaker's size.
(Note: Large speakers can fully reproduce low

frequencies of below 80Hz. Small speaker cannot
reproduce low frequencies of below 80Hz with
sufficient volume. Refer to your speaker
specifications to select the correct size).

DELAY TIME
The delay time can be individually set for the Dolby
Digital/Dolby Pro Logic II modes using the DELAY
(CENTER/REAR) buttons.
When you adjust the delay time in the Dolby Digital
mode, an additional 15 ms is automatically added to
the surround channels in the Dolby Pro Logic mode.
The current setting is shown on the display.

DELAY

TIME

BASS

MEMORY

TREBLE

DIMMER

VOL

SUBWOOFER

ON/OFF

TUNING

BASS

MODE

MUTE

POW ER

INPUT MODE

LFE TRIM

TEST

TONE

DELAY TIME

TUNER

VIDEO 1

AUX

VIDEO 2

TAPE

DVD

APS

BAND

MANUAL

ST/MONO

SURROUND

MODE

SELECT

DTS/DOLBY

DIG ITAL

VOL

PRESET +

PRESET

AG20D

1. Press "DELAY TIME" on the remote control
repeatedly, the corresponding speaker appears on
the display: S → C
2. Press +/- button to set the time delay.

Delay Time Setting Adjustable Range
    DOLBY DIGITAL MODES:
    0-15 ms in 5 ms step (S-Delay)
    0-5 ms in 1 ms step (C-Delay)
    DOLBY PRO LOGIC II MODE:
    10-25 ms in 5 ms step (S-Delay)

In the surround modes, the sound from the speakers
should be delayed slightly, relative to that from the
front speakers.
The optimum delay time will depend on acoustic
properties, whether the walls and furnishings reflect
or absorb sound, etc.
It is recommended that you try different delay times
to obtain the best effect. The delay is digitally
synthesized.
For the highest sound quality with minimum noise
and distortion, the delay time can be set
independently for each surround mode using the
DELAY TIME buttons, with the current setting shown
in the display.

DYNAMIC RANGE CONTROL
This button controls the compression range of sound
track. If the compression is large (DRC = 4/4), the
sound effect is retarded to a certain range. As a
result, sound effect is not as excited as normal range
DRC = 0/4). It is useful when you want to movies at
the late night.

Press DYNAMIC on remote control repeatedly
until the desired compression range reached.

DYNAMIC

BASS

MEMORY

TREBLE

DIMME R

VOL

SUBWOOFER

ON/OFF

TUNING

BASS

MODE

MUTE

POWER

INPUT MODE

LFE TRIM

TEST

TONE

DELAY TIME

TUNER

VIDEO 1

AUX

VIDEO 2

TAPE

DVD

APS

BAND

MANUAL

ST/MONO

SURROUND

MODE

SELECT

DTS/DOLBY

DIGITAL

VOL

PRESET +

PRESET

AG20D

DRC=0/4 No Compression
DRC=1/4
DRC=2/4
DRC=3/4
DRC=4/4 Greatest Compression
Note:
1. The Dynamic Range Control state will resume to

normal if you do not press it after 5 seconds.

2. Dynamic Range Compression is not possible with

DTS sources.