Denon S-302 Manuel D’Utilisation
Connections
Set
up
up
Pla
ybac
ybac
k
Remot
Remot
e Contr
ol
Inf
or
or
mation
Tr
oubleshooting
ENGLISH
Check that the following parts are supplied with the product.
q
Remote control (RC-1072) ....................................................... 1
w
R6P/AA batteries ..................................................................... 2
e
System cable (D-SUB25P) (Cord length: Approx. 10 ft/3 m) .... 1
r
Speaker cable (Cord length: Approx. 16 ft/5 m) ....................... 2
t
Video cable (Cord length: Approx. 5 ft/1.5 m) .......................... 1
y
AM loop antenna ..................................................................... 1
u
FM indoor antenna .................................................................. 1
i
Speaker stand .......................................................................... 2
o
Wall bracket ............................................................................. 2
Q0
Screw ...................................................................................... 4
Q1
Hex wrench ............................................................................. 1
Q2
Rod antenna for wireless LAN ................................................. 1
Q3
Anti slip pads ........................................................................... 4
Q4
Owner’s manual (with Quick setup sheet ) ............................. 1
Q5
Warranty (for North America model only ) ............................... 1
Q6
Service station list ................................................................... 1
w
e
y
u
t
q
r
Q0
Q1
Q2
o
i
Thank you for purchasing this DENON product. To ensure proper
operation, please read these owner’s manual carefully before using
the product.
After reading them, be sure to keep them for future reference.
operation, please read these owner’s manual carefully before using
the product.
After reading them, be sure to keep them for future reference.
Getting Started
• Before turning the power switch on
Check once again that all connections are correct and that there are
Check once again that all connections are correct and that there are
no problems with the connection cables.
•
Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
• Sufficiently ventilate the place of installation
If the unit is left in a room full of the smoke from cigarettes, etc., for
If the unit is left in a room full of the smoke from cigarettes, etc., for
long periods of time, the surface of the optical pickup could get dirty,
in which case it will not be able to read the signals properly.
in which case it will not be able to read the signals properly.
• About condensation
If there is a major difference in temperature between the inside of
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
before using the unit.
• Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
• Moving the unit
Turn off the power and unplug the power cord from the power
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units before
moving the unit.
•
Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
actual unit for explanation purposes.
Accessories
Cautions on Handling
DVD surround receiver
Unit name : ADV-S302
Speaker
Unit name : SC-S302
Sub woofer
Unit name : DSW-S302
System Configuration
Advanced Operation
Setting the Sleep Timer ·······························································38
Other Functions ············································································38
Setting the Sleep Timer ·······························································38
Other Functions ············································································38
Adjusting the Tone ········································································38
Turning the Sound Off Temporarily (Muting) ·································38
Turning the Sound Off Temporarily (Muting) ·································38
Convenient Functions ··································································39
Personal Memory Plus Function ··················································39
Last Function Memory ·································································39
Backup Memory ···········································································39
Auto Power On ·············································································39
Resetting the Microprocessor ······················································39
Last Function Memory ·································································39
Backup Memory ···········································································39
Auto Power On ·············································································39
Resetting the Microprocessor ······················································39
Troubleshooting ···································································46 ~ 49
Specifications ··············································································· 50
Other Information ································································42 ~ 45
List of preset codes ··········································· End of this manual
Remote Control Unit Operations
Setting the preset memory function ············································40
Operating a component stored in the preset memory ················40
Setting the punch through function ········································40, 41
Operating a component stored in the preset memory ················40
Setting the punch through function ········································40, 41
Get
ting Star
ting Star
ted
1.S-302E3_1st.indd 6
2007/07/31 17:44:21