Dantax LR-6500 Manuel D’Utilisation
- 21 -
Tuner Operation
AM/FM
SELECT
SOURCE
TUN/PRE
T.MODE
AM/FM
NUMERIC
TUNING
MEMO
DIRECT
TUN-M
PRESET
The LR-6500's tuner is capable of tuning AM,FM and FM
Stereo broadcast stations. Stations may be tuned manually,
or they may be stored as favorite station presets and
recalled from a 50-position memory.
Stereo broadcast stations. Stations may be tuned manually,
or they may be stored as favorite station presets and
recalled from a 50-position memory.
Station Selection
Press the AM/FM button on the remote controller to
select the tuner as an input
select the tuner as an input
or
The tuner may be selected from the front panel by either
pressing the SOURCE (6/n) buttons until the tuner is
active or by pressing the AM/FM button.
pressing the SOURCE (6/n) buttons until the tuner is
active or by pressing the AM/FM button.
Pressing the AM/FM button or the AM/FM button on the
front panel again to switch between AM and FM so that
the desired frequency band is selected.
front panel again to switch between AM and FM so that
the desired frequency band is selected.
Press the T.MODE on the front panel (or the TUN-M but-
ton on the remote controller) to select manual or auto-
matic tuning.
ton on the remote controller) to select manual or auto-
matic tuning.
Select "AUTO TUNING" and each press of the
TUNING(v/^) button (or TUN/PRE button). Then put the
tuner in a scan mode that seek the next higher or lower
frequency station with acceptable signal strength.
TUNING(v/^) button (or TUN/PRE button). Then put the
tuner in a scan mode that seek the next higher or lower
frequency station with acceptable signal strength.
• Select "MAUNAL TUNING" and each press of the TUN-
ING(v/^) button (or TUN/PRE button). The frequency
increases or decreases by one increment.
increases or decreases by one increment.
Stations may also be tuned directly. To enter a station's
frequency directly, first select the AM or FM. Next, press
the DIRECT button on the remote controller and enter
the station frequency by pressing the Numeric buttons.
frequency directly, first select the AM or FM. Next, press
the DIRECT button on the remote controller and enter
the station frequency by pressing the Numeric buttons.
5
4
3
2
1
Tuner-Mode
Pressing the TUN-M button on the
remote controller
alternates between Stereo mode and Mono mode.
- STEREO
FM stereo broadcasts are received in stereo and the
STEREO indicator lights in the display.
STEREO indicator lights in the display.
- MONO
To compensate for weak FM stereo reception, select
this mode. Reception will now be forced monaural,
reducing unwanted noise.
this mode. Reception will now be forced monaural,
reducing unwanted noise.
Preset Memory
You can preset a maximum of 50 favorite channels.
Press the MEMO button. The two underscore lines will
appear at the far right side of the display.
appear at the far right side of the display.
Within 5 seconds, press the Numeric buttons corre-
sponding to the location where you wish to store this
station's frequency.
sponding to the location where you wish to store this
station's frequency.
Repeat the process after tuning any additional stations
to be preset.
to be preset.
Recalling Preset Stations
• To manually select a station previously entered in the pre-
set memory, press the Numeric buttons that correspond
to the desired station's memory location.
to the desired station's memory location.
• To manually tune through the list of stored preset stations
one by one, press the PRESET(v/^) button or the remote
controller or the TUN/PRE (6/n) button on the front
panel.
controller or the TUN/PRE (6/n) button on the front
panel.
3
2
1