Shure i2c-t Fascicule
Audio source:
cell phone
media player
I2c-T
Sound Isolating Earphones
These sound-isolating earphones
with VoicePort inline microphone
connect to your integrated media
player cell phone. They feature
Dynamic MicroDriver technology
that you can now enjoy at low
listening levels, even in noisy
environments.
INSERTING THE EARPHONES
If the earphone seems to be lacking in low frequency response (bass), check
the tightness of the seal between the earphone and your ear, or try one of the
other sleeve options.
the tightness of the seal between the earphone and your ear, or try one of the
other sleeve options.
Warning: Do not push the earphone sleeve beyond the ear canal opening.
WEARING THE EARPHONES
CHOOSING AN EARPHONE SLEEVE
Your earphones come with a selection of sleeves. Make sure the sleeve you
use is easy to insert into your ear, fits comfortably, and is easy to remove from
your ear.
use is easy to insert into your ear, fits comfortably, and is easy to remove from
your ear.
WAX GUARD
You should place wax guards on the nozzle of your I2c-T earphones before
using them. These protective rings are found on an adhesive strip in the fit kit
that comes with your earphones.
To place a wax guard on one of your I2c-T earphones:
using them. These protective rings are found on an adhesive strip in the fit kit
that comes with your earphones.
To place a wax guard on one of your I2c-T earphones:
Remove the sleeve from the earphone nozzle.
If there is a dirty wax guard on the earphone, peel it off.
Clean the tip of the I2c-T nozzle with an antiseptic or alcohol wipe.
Make sure that the tip of the nozzle is dry, then remove a wax guard from the
supplied strip and place it on the tip of the nozzle, adhesive side down.
Replace the sleeve on the earphone.
If there is a dirty wax guard on the earphone, peel it off.
Clean the tip of the I2c-T nozzle with an antiseptic or alcohol wipe.
Make sure that the tip of the nozzle is dry, then remove a wax guard from the
supplied strip and place it on the tip of the nozzle, adhesive side down.
Replace the sleeve on the earphone.
1.
2.
3.
4.
2.
3.
4.
5.
Make sure that the sleeve completely
covers the earphone stem. If any part
of the nozzle is exposed, the sleeve is
not properly installed.
covers the earphone stem. If any part
of the nozzle is exposed, the sleeve is
not properly installed.
Foam Sleeves
When using the foam sleeves, compress the sleeve between
your fingers before inserting it into the ear canal. Hold the
earphone in place for about ten seconds while the foam
expands and creates a tight seal.
When using the foam sleeves, compress the sleeve between
your fingers before inserting it into the ear canal. Hold the
earphone in place for about ten seconds while the foam
expands and creates a tight seal.
Soft Flex Sleeves
In small, medium, and large sizes. Made from pliable rubber.
In small, medium, and large sizes. Made from pliable rubber.
Stem
Wax Guard
IMPORTANT: Do not place wax guards on sleeves! Wax guards are intended for use on
the tip of the earphone nozzle only. If wax guards are placed on sleeves they will not
function properly and may fall off the sleeves into your ears.
the tip of the earphone nozzle only. If wax guards are placed on sleeves they will not
function properly and may fall off the sleeves into your ears.
©2005, Shure Incorporated
27EN3209 (Rev. 2)
27EN3209 (Rev. 2)
Printed in U.S.A.
Flex Sleeves
In small, medium, and large sizes. Made from translucent
PVC.
In small, medium, and large sizes. Made from translucent
PVC.
Over the ear
in front
left ear
right ear
INLINE SWITCH CONTROL
Push and hold to MUTE cell phone microphone
Volume
Note: Turn volume control to its lowest setting before switching be-
tween music and cell phone. Switching to media during a call mutes
cell phone.
tween music and cell phone. Switching to media during a call mutes
cell phone.
Wear the earphones as illustrated below.