Sony MZ-R700 Manuel D’Utilisation
31
MZ-G750/R700
Pin No.
Pin Name
I/O
Description
52
AVD2
—
Power supply terminal (for the analog) (+2.4 V)
53
AVS2
—
Ground terminal (for the analog)
54
ADRB
I
A/D converter the lower limit voltage input (fixed at “L” in this set)
55
SE
I
Sled error signal input terminal Not used (fixed at “L”)
56
TE
I
Tracking error signal input from RF amp (IC501)
57
DCHG
—
Connecting analog power supply of the low impedance (fixed at “H” in this set)
58
APC
I
Error signal input for the laser automatic power control Not used (fixed at “H”)
59
DSPVDD0
—
Power supply terminal (for DSP block) (+1.5 V)
60
DSPVSS0
—
Ground terminal (for DSP block)
61
XTSL
I
Input terminal for the frequency set up of the system clock
“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “L” in this set)
62
DIN1
I
Input terminal of the record system digital audio signal
63
DOUT
O
Output terminal of the playback system digital audio signal Not used (open)
64
DAPWMLP
O
D/A converter PWM output (L-CH right phase) Not used (open)
65
DAPWMLN
O
D/A converter PWM output (L-CH reverse phase) Not used (open)
66
DAPWMRP
O
D/A converter PWM output (R-CH right phase) Not used (open)
67
DADT
O
Audio data output Not used (open)
68
ADDT
I
Data signal input from the external A/D converter (IC301)
69
LRCK
O
L/R sampling block signal (44.1 kHz) output to the external A/D converter (IC301)
70
XBCK
O
Bit clock signal (2.8224 MHz) output to the external A/D converter (IC301)
71
FS256
O
11.2896 MHz clock signal output to the external A/D converter (IC301)
72
MVCI
I
Vibrate input for the digital in PLL from the external VCO Not used (fixed at “L”)
73
DSPVDD1
—
Power supply terminal (for DSP block) (+1.5 V)
74
ADFG
I
ADIP duplex FM signal (20.05 ± 1 kHz) input from RF amp (IC501)
75
F0CNT
O
Filter cut off control signal output Not used
76
DIFVDD0
—
Power supply terminal (for DSP I/F) (+2.3 V)
77
DIFVSS0
—
Ground terminal (for DSP I/F)
78
APCREF
O
Control signal output to the reference voltage generation circuit for the laser
automatic power control
79
LDDR
O
PWM signal output for the laser automatic power control Not used (open)
80
TRDR
O
Tracking servo drive PWM signal output (–) to the motor driver (IC551)
81
TFDR
O
Tracking servo drive PWM signal output (+) to the motor driver (IC551)
82
FFDR
O
Focus servo drive PWM signal output (+) to the motor driver (IC551)
83
FRDR
O
Focus servo drive PWM signal output (–) to the motor driver (IC551)
84
MCUVDD1
—
Power supply terminal (for the microcomputer block) (+1.5 V)
85
FGIN
I
FG signal input terminal for the spindle servo Not used (open)
86
FS4
O
176.4 MHz clock signal output to the power control (IC601, IC901)
87
SPRD/SPDU/RTG0
O
Spindle servo drive PWM signal output terminal (–) to the motor driver (IC551)
88
SPFD/SPVS/PWM3
O
Spindle servo drive PWM signal output (+)
89
SPDV/RTG1
O
Spindle motor drive control signal output (V)/RTG output 1 to the motor
driver (IC551)
90
SPDW/RTG2
O
Spindle motor drive control signal output (W)/RTG output 2 to the motor
driver (IC551)
91
DSPVDD2
—
Power supply terminal (for DSP block) (+1.5 V)
92
DSPVSS1
—
Ground terminal (for DSP block)
93
SPCU
I
Spindle motor drive comparison signal input (U) from the motor driver (IC551)
94
SPCV
I
Spindle motor drive comparison signal input (V) from the motor driver (IC551)
95
SPCW
I
Spindle motor drive comparison signal input (W) from the motor driver (IC551)
96
SRDR
O
Sled servo drive PWM signal output (–) to the motor driver (IC551)
97
SFDR
O
Sled servo drive PWM signal output (+) to the motor driver (IC551)
98
SLDV
O
Sled motor drive signal output (V) to the motor driver (IC551)/drive control signal
output (1–)