ONKYO SR575 Manuel D’Utilisation
63
Controlling Other Components
—Continued
Onkyo components that are connected via
are con-
trolled by pointing the remote controller at the AV
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
receiver, not the component. This allows you to control
components that are out of view, in a rack, for example.
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
, use
the following remote control codes:
• [DVD] REMOTE MODE button
• [DVD] REMOTE MODE button
0627:
Onkyo DVD player without
(default)
• [CD/MD/CDR/DOCK] REMOTE MODE button
1817:
Onkyo CD player without
(default)
0868:
Onkyo MD recorder without
1323:
Onkyo CD recorder without
2990:
Onkyo RI Dock without
Note:
If you connect an
-capable Onkyo MD recorder, CD
recorder, or RI Dock component to the TAPE IN/OUT or
CBL/SAT jacks, for remote operation to work properly,
you must set the Input Display to MD, CDR, or DOCK
(see page 39).
CBL/SAT jacks, for remote operation to work properly,
you must set the Input Display to MD, CDR, or DOCK
(see page 39).
You can reset a REMOTE MODE button to its default
remote control code.
remote control code.
You can reset the remote controller to its default settings.
Remote Control Codes for Onkyo
Components Connected via
Components Connected via
1
Make sure the Onkyo component is con-
nected with an
nected with an
cable and an analog
audio cable (RCA).
2
Enter the appropriate remote control code
for the [DVD] or [CD] REMOTE MODE but-
ton.
for the [DVD] or [CD] REMOTE MODE but-
ton.
[DVD] REMOTE MODE button
1612:
Onkyo DVD player with
[CD/MD/CDR/DOCK] REMOTE MODE button
1327:
Onkyo CD player with
1808:
Onkyo MD recorder with
1322:
Onkyo CD recorder with
1993:
Onkyo RI Dock with
See the previous page for how to enter remote
control codes.
control codes.
3
Press the [DVD] or [CD] REMOTE MODE
button, point the remote controller at the
AV receiver, and operate the component.
button, point the remote controller at the
AV receiver, and operate the component.
Resetting REMOTE MODE Buttons
1
While holding down the REMOTE
MODE button that you want to
reset, press the [L NIGHT] button
for 3 seconds.
MODE button that you want to
reset, press the [L NIGHT] button
for 3 seconds.
The REMOTE MODE button lights up.
2
Press the REMOTE MODE button
again.
again.
The REMOTE MODE button flashes
twice, indicating that it’s been reset.
twice, indicating that it’s been reset.
The [DVD] and [CD] REMOTE
MODE buttons are preprogrammed
with remote control codes for control-
ling Onkyo DVD players and CD play-
ers respectively. When these buttons
are reset, the preprogrammed code is
restored.
MODE buttons are preprogrammed
with remote control codes for control-
ling Onkyo DVD players and CD play-
ers respectively. When these buttons
are reset, the preprogrammed code is
restored.
Resetting the Remote Controller
1
While holding down the
[RECEIVER] REMOTE MODE but-
ton, press the [L NIGHT] button
for 3 seconds.
[RECEIVER] REMOTE MODE but-
ton, press the [L NIGHT] button
for 3 seconds.
The [RECEIVER] button lights up.
2
Press the [RECEIVER] REMOTE
MODE button again.
MODE button again.
The [RECEIVER] button flashes twice,
indicating that it’s been reset.
indicating that it’s been reset.
M D/CDR
DOCK
CABLE
REMOTE MODE
SAT
VCR
T V
DVD
C D
L NIGHT
M D/CDR
DOCK
CABLE
REMOTE MODE
SAT
VCR
T V
DVD
C D
RECEIVER
L NIGHT
RECEIVER
TX-SR505_En.book Page 63 Tuesday, January 30, 2007 11:53 AM