ONKYO TX-NR626 Manuel D’Utilisation

Page de 140
Advanced Operations
En-63
You can assign a default listening mode to each input 
source that will be selected automatically when you 
select each input source. For example, you can set 
the default listening mode to be used with Dolby 
Digital input signals. You can select other listening 
modes during playback, but the mode specified here 
will be resumed once the AV receiver has been set to 
standby.
Analog/PCM/Digital
With this setting, you can specify the listening mode 
used when an analog (CD, TV, LD, VHS, MD, 
turntable, radio, cassette, cable, satellite, etc.) or 
PCM digital (CD, DVD, etc.) audio signal is played.
Mono/Multiplex Source
With this setting, you can specify the listening mode 
used when a mono digital audio signal is played 
(DVD, etc.).
2ch Source
With this setting, you can specify the listening mode 
used when 2-channel (2/0) stereo digital sources, 
such as Dolby Digital or DTS, are played.
Dolby D/Dolby D Plus/TrueHD
With this setting, you can specify the listening mode 
used when Dolby Digital or Dolby Digital Plus 
format digital audio signals are played (DVD, etc.). 
Specifies the default listening mode for Dolby 
TrueHD sources, such as Blu-ray or HD DVD (input 
via HDMI).
DTS/DTS-ES/DTS-HD
With this setting, you can specify the listening mode 
used when DTS or DTS-HD High Resolution format 
digital audio signals are played (DVD, LD, CD, 
etc.). Specifies the default listening mode for DTS-
HD Master Audio sources, such as Blu-ray or HD 
DVD (input via HDMI).
Other Multich Source
Specifies the default listening mode for 
multichannel PCM sources from HDMI IN such as 
DVD-Audio, and DSD multichannel sources such 
as Super Audio CD.
Volume Setup
Maximum Volume
`
Off30 to 79
With this setting, you can limit the maximum volume.
To disable this setting, select “Off”.
Power On Volume
`
LastMin1 to 79 or Max
With this preference, you can specify the volume 
setting to be used each time the AV receiver is turned 
on.
To use the same volume level that was used when 
the AV receiver was turned off, select “Last”.
The “Power On Volume” setting cannot be set higher 
than the “Maximum Volume” setting.
Headphone Level
`
–12dB to 0dB to +12dB
With this setting, you can specify the headphone 
volume relative to the main volume. This is useful if 
there’s a volume difference between your speakers 
and your headphones.
5. Listening Mode Preset
1
Use 
q/w to select the input source that you 
want to set, and then press ENTER.
The following menu appears.
2
Use 
q/w to select the signal format that you 
want to set, and then use 
e/r to select a 
listening mode.
Only listening modes that can be used with each 
input signal format can be selected (
 
).
The “Last Valid” option means that the listening 
mode selected last will be used.
The “Straight Decode” option means that 
straight decoding listening mode (Dolby Digital, 
DTS, etc.) is selected.
Note
• For the “TUNER” input selector, only “Analog” will be 
available.
• For the “NET” or “USB input selector, “Digital” and 
TrueHD“ will be available.
Default listening mode for analog and PCM sources.
Analog/PCM
Mono/Multiplex Source
2ch Source
Dolby D/Dolby D Plus/TrueHD
DTS/DTS-ES/DTS-HD
Other Multich Source
Last Valid 
e r
5-1. Listening Mode Preset
BD/DVD
Last Valid
Last Valid
Last Valid
Last Valid
Last Valid
• For the “BLUETOOTH” input selector, only “Digital” 
is available.
6. Miscellaneous