ONKYO TX-NR626 Manuel D’Utilisation
Controlling Other Components
En-72
You can change the configuration of colored buttons,
with which REMOTE MODE buttons are preset.
with which REMOTE MODE buttons are preset.
Tip
• To reset the REMOTE MODE buttons to their default
Note
• If any other button than the colored buttons is pressed, the
operation will be cancelled.
• This operation cannot be done while the AV receiver is in
Receiver mode or when Zone 2 is active.
Onkyo components that are connected via
u are
controlled by pointing the remote controller at the AV
receiver, not the component. This allows you to
control components that are out of view, in a rack, for
example.
receiver, not the component. This allows you to
control components that are out of view, in a rack, for
example.
Controlling Onkyo components without
u
If you want to control an Onkyo component by
pointing the remote controller directly at it, or you
want to control an Onkyo component that’s not
connected via
pointing the remote controller directly at it, or you
want to control an Onkyo component that’s not
connected via
u, use the following remote control
codes:
`
30627:
Onkyo DVD player without
u
`
71817:
Onkyo CD player without
u
`
32900/33100/33500:
Onkyo Blu-ray Disc player
`
32901/33104/33504:
Onkyo HD DVD player
`
70868:
Onkyo MD recorder without
u
`
71323:
Onkyo CD recorder without
u
`
82990:
Onkyo Dock without
u
You can reset a REMOTE MODE button to its default
remote control code.
remote control code.
You can reset the remote controller to its default
settings.
settings.
Remapping Colored Buttons
1
While holding down the REMOTE MODE
button that you want to program, press and
hold down A (Red) until the remote indicator
lights (about 3 seconds).
You can only change colored buttons for
components whose codes belong to categories
of the Remote Control Codes list (BD/DVD
player, TV, cable set-top box, etc).
button that you want to program, press and
hold down A (Red) until the remote indicator
lights (about 3 seconds).
You can only change colored buttons for
components whose codes belong to categories
of the Remote Control Codes list (BD/DVD
player, TV, cable set-top box, etc).
2
Within 30 seconds, press the colored buttons
in the order that you want to reassign them.
The button presses are assigned to each button
from left to right. The remote indicator flashes
twice, indicating that the sequence has been
successfully assigned. If the sequence is not
successfully assigned, the remote indicator will
flash once slowly.
in the order that you want to reassign them.
The button presses are assigned to each button
from left to right. The remote indicator flashes
twice, indicating that the sequence has been
successfully assigned. If the sequence is not
successfully assigned, the remote indicator will
flash once slowly.
Remote Control Codes for Onkyo
Components Connected via RI
Components Connected via RI
1
Make sure the Onkyo component is connected
with an
with an
u cable and an analog audio cable
2
Enter the appropriate remote control code for
a REMOTE MODE button, by referring to the
previous section.
a REMOTE MODE button, by referring to the
previous section.
`
42157:
Onkyo cassette tape deck with
u
`
81993:
Onkyo Dock with
u
3
Press the REMOTE MODE button, point the
remote controller at the AV receiver, and
operate the component.
remote controller at the AV receiver, and
operate the component.
Resetting the REMOTE MODE Buttons
1
While holding down the REMOTE MODE
button that you want to reset, press and hold
down HOME until the remote indicator lights
(about 3 seconds).
button that you want to reset, press and hold
down HOME until the remote indicator lights
(about 3 seconds).
2
Within 30 seconds, press the REMOTE MODE
button again.
The remote indicator flashes twice, indicating that
the button has been reset.
Each REMOTE MODE button is preprogrammed
with a remote control code. When a button is
reset, its preprogrammed code is restored.
button again.
The remote indicator flashes twice, indicating that
the button has been reset.
Each REMOTE MODE button is preprogrammed
with a remote control code. When a button is
reset, its preprogrammed code is restored.
Resetting the Remote Controller
1
While holding down RECEIVER, press and
hold down HOME until the remote indicator
lights (about 3 seconds).
hold down HOME until the remote indicator
lights (about 3 seconds).
2
Within 30 seconds, press RECEIVER again.
The remote indicator flashes twice, indicating that
the remote controller has been reset.
The remote indicator flashes twice, indicating that
the remote controller has been reset.