ONKYO TX-NR3009 Manuel D’Utilisation
44
En
You can adjust the brightness of the AV receiver’s
display.
display.
You can display various information about the current
input source as follows. (Components connected to the
UNIVERSAL PORT jack are excluded.)
input source as follows. (Components connected to the
UNIVERSAL PORT jack are excluded.)
The following information can typically be displayed.
*1
If the input signal is PCM, the sampling frequency is
displayed. If the input signal is digital but not PCM, the signal
format is displayed. Information is displayed for about three
seconds, then the previously displayed information reappears.
displayed. If the input signal is digital but not PCM, the signal
format is displayed. Information is displayed for about three
seconds, then the previously displayed information reappears.
When you connect an
u-capable Onkyo component, you
must configure the input display so that
u can work
properly.
This setting can be done only from the front panel.
This setting can be done only from the front panel.
The Whole House Mode is useful when you want to add
extra background music to your home party; this allows
you to enjoy the same stereo music as the main room in
separate rooms (Multi Zone: Powered Zone 2/3).
The Whole House Mode selects the same input source for
Multi Zone as the main room’s.
See also:
• “Speaker Setup” (
extra background music to your home party; this allows
you to enjoy the same stereo music as the main room in
separate rooms (Multi Zone: Powered Zone 2/3).
The Whole House Mode selects the same input source for
Multi Zone as the main room’s.
See also:
• “Speaker Setup” (
Setting the Display Brightness
1
Press
RECEIVER followed by DIMMER
repeatedly to select:
• Normal + MASTER VOLUME and input selector
• Normal + MASTER VOLUME and input selector
indicators light.
• Normal + MASTER VOLUME and input selector
indicators go off.
• Dim + MASTER VOLUME and input selector
indicators go off.
• Dimmer + MASTER VOLUME and input selector
indicators go off.
Tip
• (North American models) Alternatively, you can use the
AV receiver’s DIMMER.
Displaying Source Information
1
Press
RECEIVER followed by DISPLAY
repeatedly to cycle through the available
information.
information.
Tip
• Alternatively, you can use the AV receiver’s DISPLAY.
Input source
Input signal
resolution
Output
resolution
Signal format
*1
Listening mode
Sampling
frequency
Changing the Input Display
1
Press
TV/CD, GAME or VCR/DVR.
“TV/CD”, “GAME” or “VCR/DVR” appears on the
display.
display.
2
Press and hold down
TV/CD, GAME or VCR/DVR
(about 3 seconds) to change the input display.
Repeat this step to select the desired input display.
Repeat this step to select the desired input display.
Note
• DOCK can be selected for the TV/CD, GAME or
VCR/DVR input selector, but not at the same time.
• Enter the appropriate remote control code before using the
remote controller for the first time (
).
Using the Whole House Mode
1
Press
WHOLE HOUSE MODE on the front panel.
To cancel the Whole House Mode, change the input
source for the main room or select a listening mode
(
source for the main room or select a listening mode
(
).
Note
• The Whole House Mode only supports analog audio.
• To use the Whole House Mode, Powered Zone 2/3 must be
• To use the Whole House Mode, Powered Zone 2/3 must be
set to enabled (
• Cancelling the Whole House Mode will switch Multi Zone
off.
• The sound from Powered Zone 2/3 may interrupt when
turning the Whole House Mode on or off.
• If you change the setting of Multi Zone while using the
Whole House Mode, this setting prevails over the Whole
House Mode’s.
House Mode’s.
• To adjust the volume of Multi Zone, switch the AV
receiver to Multi Zone control. See “Adjusting the Volume
for Zones” (
for Zones” (
) for the volume adjustment of
Multi Zone.
• The Whole House Mode cannot be used while the “Audio
TV Out” setting is on.
TV/CD
→
DOCK
→
→
TAPE
■
TV/CD:
GAME
↔ DOCK
■
GAME:
VCR/DVR
↔ DOCK
■
VCR/DVR: