ONKYO tx-nr545 Manuel D’Utilisation

Step 2: Initial Setup

En-12



The subwoofer sound may not be detected since it is extremely

low frequencies. Set the subwoofer volume to around the half of its

maximum volume and make its frequency to the maximum level.



Measurement may be interrupted if there is ambient noise or radio

frequency interference. Close the window and turn off the home

appliance and fluorescent light.

2� After placing the microphone at the measurement

position, select "Do it Now" with the cursors and

press ENTER�

3� When "Please plug microphone that came in a

box with AV receiver" is displayed, connect the

microphone to the SETUP MIC jack of the unit�

SETUP MIC jack

Calibration

microphone

4� Select the settings for the connected speakers, the

type of the height speakers, and other appropriate

settings�

AccuEQ Room Calibration

Speaker Channels
Subwoofer
Height Speaker
Bi-Amp
Powered Zone2

7.1ch

Yes
-----

No
No

ENTER

Select how many speakers you have.

When the screen above is displayed, set the items with

the cursor buttons on the remote controller. Refer to

the on-screen diagram for "Speaker Channels", which

changes each time a different number of channels

is selected. When all the items have been set, press

ENTER on the remote controller. After that, follow the

guidance displayed on the TV screen to operate the unit.

● Refer to the content of an item, which appears on

the lower left of the screen when the cursor is on the

item.

5� The test tones sound from the connected speakers

and automatic speaker setting starts�

Measurement will be made 3 times or more for each

speaker. It takes several minutes to be completed. Keep

the room as quiet as possible during measurement. If

any of the speakers do not produce the test tone, check

for disconnection.

● During measurement, each speaker outputs the test

tones at a high volume. Be careful of sound leak

that may disturb your neighbors, or be careful not to

frighten young children.

6� When the measurement is completed, the

measurement result is displayed�

Press

on the remote controller to check the

settings. Press ENTER with "Save" selected. Select

"On" in the next screen and press ENTER on the remote

controller.

● You should normally select "On (All Channels)", and

to disable just the front speakers, you should select

"On (Except Front Left/Right)".

● If there is an error message, follow the on-screen

instruction to remove the error cause.

7� When "Please unplug setup microphone�" is

displayed, disconnect the microphone�

Source Connection

You can check the connections on the different inputs and

make HDMI link function settings.
1� When the Source Connection start screen is

displayed, select "Yes, Continue" with the cursors

and press ENTER�

Source Connection
This step will start to check if the
connections were made correctly.
Would you like to continue?

Yes. Continue
No. Skip

Initial Setup

Exit

SETUP

2� Select the desired input to check the connection and

press ENTER�

Start playback of the selected device. If connection is

correct, video/audio of the input source selected on the

unit will be played.

3� After checking the connection, select "Yes" with the

cursors and press ENTER�

● If you select "No" and press ENTER, the error cause

will be displayed. Follow the guidance to remove the

error cause and check the connection again.

4� Select "Yes" with the cursors and press ENTER

on the remote controller to check the connection

of other inputs or select "No, Done Checking" and

press ENTER to skip�

If you select "Yes", you will return to the screen of step

If you select "No, Done Checking", you will proceed to

step 5.

5� Set the CEC link function�

Select "Yes" to enable the HDMI link function with CEC-

compliant equipment, then select "Yes" again in the next

screen.

The following CEC-compatible devices are found;
Do you wish to turn on the CEC link?
xxxxxxxxxxx

Yes
No

Source Connection

Exit

SETUP

If you select "Yes", the connection with ARC compatible

TV and HDMI Standby Through function will be set to

"On" and enabled.