ONKYO 29400021 Manuel D’Utilisation
121
Notes:
• Only analog input sources are output by the ZONE 2/
• Only analog input sources are output by the ZONE 2/
3 PRE OUT and ZONE 2/3 L/R speaker terminals.
Digital input sources are not output. If no sound is
heard when an input source is selected, check if it’s
connected to an analog input.
Digital input sources are not output. If no sound is
heard when an input source is selected, check if it’s
connected to an analog input.
• You cannot select different AM or FM radio stations
for your main room and Zone 2/3. The same AM/FM
radio station will be heard in each room. For example,
if you have an FM station for the main room, that sta-
tion will also be used in Zone 2.
radio station will be heard in each room. For example,
if you have an FM station for the main room, that sta-
tion will also be used in Zone 2.
• When you connect Zone 2 speakers directly to the AV
receiver, listening modes that require surround back
speakers or front high speakers or front wide speakers
(6.1/7.1), such as Dolby Digital EX, DTS-ES, THX
Select2 Cinema, Dolby Pro Logic IIz height, and
Audyssey Dynamic Surround Expansion™ are
unavailable.
speakers or front high speakers or front wide speakers
(6.1/7.1), such as Dolby Digital EX, DTS-ES, THX
Select2 Cinema, Dolby Pro Logic IIz height, and
Audyssey Dynamic Surround Expansion™ are
unavailable.
• When you connect Zone 3 speakers directly to the AV
receiver, listening modes that require surround speak-
ers are unavailable.
ers are unavailable.
• When the input selector of Zone 2/3 is selected, power
consumption on standby mode slightly increases.
• While Zone 2/3 is on,
u functions will not work.
Adjusting the Volume for Zones
Muting Zones
Adjusting the Tone and Balance of Zones
Notes:
• Zones can also be unmuted by adjusting the volume.
• The Zone 2 volume, tone, and balance function have
• Zones can also be unmuted by adjusting the volume.
• The Zone 2 volume, tone, and balance function have
no effect on the ZONE 2 PRE OUT when the “Zone2
Out” setting is set to “Fixed” (page 119).
Out” setting is set to “Fixed” (page 119).
• The Zone 3 volume, and balance function have no
effect on the ZONE 3 PRE OUT when the “Zone3
Out” setting is set to “Fixed” (page 119).
Out” setting is set to “Fixed” (page 119).
• Even if you repeatedly press the remote controller’s
[ZONE] button to select zones, the last zone selection
will be retained once you have switched to other com-
ponents by pressing other REMOTE MODE buttons
after pressing the [ZONE] button.
will be retained once you have switched to other com-
ponents by pressing other REMOTE MODE buttons
after pressing the [ZONE] button.
Remote
controller
On the remote controller, press
the [ZONE] button repeatedly,
and then use the VOL [
the [ZONE] button repeatedly,
and then use the VOL [
q]/[w]
button.
AV receiver
On the AV receiver, press the
[ZONE 2] or [ZONE 3] button (the
ZONE 2/3 indicator and Zone 2/3
selector on the display flashes)
and press [LEVEL] button
followed by the [
[ZONE 2] or [ZONE 3] button (the
ZONE 2/3 indicator and Zone 2/3
selector on the display flashes)
and press [LEVEL] button
followed by the [
e]/[r] buttons
within 8 seconds.
Remote
controller
On the remote controller, press
the [ZONE] button repeatedly,
and then press the [MUTING]
button.
the [ZONE] button repeatedly,
and then press the [MUTING]
button.
To unmute a zone, on the remote
controller, press the [ZONE]
button, and then press the
[MUTING] button again.
controller, press the [ZONE]
button, and then press the
[MUTING] button again.
1
AV receiver
On the AV receiver, press the
[ZONE 2] or [ZONE 3] button.
[ZONE 2] or [ZONE 3] button.
2
Press the AV receiver’s [TONE]
button repeatedly to select
“Bass”, “Treble” or “Balance”.
button repeatedly to select
“Bass”, “Treble” or “Balance”.
3
Use the Right [
r] and Left [e]
buttons to adjust the bass, treble
or balance.
• You can boost or cut the bass or tre-
or balance.
• You can boost or cut the bass or tre-
ble from –10 dB to +10 dB in 2 dB
steps.
steps.
• You can adjust the balance from 0 in
the center to +10 dB to the right or
+10 dB to the left in 2 dB steps.
+10 dB to the left in 2 dB steps.
TX-NR807_En.book Page 121 Tuesday, July 28, 2009 12:00 PM