Sunfire Symphonic Reference High Fidelity Control Center and Preamplifier Manuel D’Utilisation
User's Manual
7
CHAPTER 1
Observe the following precautions
when choosing a location for your
preampliÞ er:
preampliÞ er:
• Do not cover any of the ventila-
tion slots.
• Do not place directly on top of
a power ampliÞ er.
• Protect it from pro longed
ex po sure to direct sunlight and
other direct sources of heat,
such as heating vents and
ra di a tors.
other direct sources of heat,
such as heating vents and
ra di a tors.
• Do not expose the unit to rain
or moisture. If ß uid or a for-
eign object should enter the
unit, immediately turn off the
power and contact your SunÞ re
Dealer.
eign object should enter the
unit, immediately turn off the
power and contact your SunÞ re
Dealer.
• Avoid excessive exposure to
extreme cold or dust.
• Do not place heavy objects on
top of the unit.
AC Power Con sid er ations
Ensure that the unit is plugged
into an outlet capable of supplying
the correct voltage speciÞ ed for your
model.
the correct voltage speciÞ ed for your
model.
Care
If you need to clean the front sur-
face, Þ rst turn off the power and then
use a dry cloth, rubbing with the grain.
Be careful not to scratch the Þ nish.
use a dry cloth, rubbing with the grain.
Be careful not to scratch the Þ nish.
Connection Tips
Before setting up your new sys-
tem, please consider the following :
Always make sure that your
com po nents are all turned
OFF, or unplugged before
making or changing any
connec tions.
OFF, or unplugged before
making or changing any
connec tions.
• Whenever possible, route the
power cords away from the
signal cables or speaker wires
signal cables or speaker wires
to pre vent any hum or in ter -
fer ence heard in the speak ers.
fer ence heard in the speak ers.
• Choose reliable hookup cables.
They should be fully shield ed
and as short as pos si ble.
and as short as pos si ble.
• Some patch cords can be a
very tight Þ t and there is usu-
ally a preferred method of get-
ting them off. Some have to be
removed with a twisting action.
Be gentle or you may dam age
the jacks of your preampliÞ er,
or other com po nents.
ally a preferred method of get-
ting them off. Some have to be
removed with a twisting action.
Be gentle or you may dam age
the jacks of your preampliÞ er,
or other com po nents.
• Some audiophile cables should
be hooked up in one direction,
these are usually marked with
arrows.
these are usually marked with
arrows.
• It is usual for the right channel
patch cord plugs to be red and
the left channel con nec tions to
be white, grey or black.
the left channel con nec tions to
be white, grey or black.
12 VDC Trigger
The preampliÞ er's Trigger termi-
nal supplies 12 VDC whenever the
preampliÞ er is turned on. This can be
used to turn on SunÞ re power ampli-
Þ ers or other equipment with a 12 V
trigger input.
preampliÞ er is turned on. This can be
used to turn on SunÞ re power ampli-
Þ ers or other equipment with a 12 V
trigger input.
Use all stan dard safe ty pre-
cau tions and make sure all
cau tions and make sure all
the equip ment is dis con nect ed
be fore making any con nec -
tions.
be fore making any con nec -
tions.
Installation
Remote Control
CD
PHONO
TUNER
VOLUME
POWER
MUTE
AUX1
AUX2
SOURCE
DIRECT
EXTERNAL
PROCESSOR
TAPE
MONITOR
STEREO/
MONO
TAPE
Symphonic Reference Preamplifier
Remote Control
Batteries
Use a small Phillips screwdriver
and undo the rear cover of the remote
to change the batteries.
to change the batteries.
Functions
Most functions of the preampliÞ er
can be operated by the remote con-
trol, except for Tone and Balance.
trol, except for Tone and Balance.
You can connect an external IR
receiver to the preampliÞ er's rear IR
port. This will allow you to operate the
preampliÞ er from a remote location.
port. This will allow you to operate the
preampliÞ er from a remote location.
Place the preampliÞ er or any
external Infrared receivers in a place
where there is a direct line of sight
from your listening position.
where there is a direct line of sight
from your listening position.