Behringer Xenyx 1002B Manuel D’Utilisation
7
XENYX 1002B User Manual
Controls and Connectors
3.
Front panel
3.1
(1)
(2)
(10)
(11)
(12)
(13)
(14)
(8)
(6)
(9)
(3)
(17)
(21)
(18)
(19)
(22)
(24)
(25)
(26)
(27)
(23)
(20)
(4)
(5)
(15)
(7)
(16)
MIC
(1)
– Plug a microphone into this input using an XLR cable.
LINE IN
(2)
– Plug a line-level source into this jack using a ¼" TS or TRS cable.
INS(ERT)
(3)
– Plug an external dynamic processor into this jack using a TRS to
dual TS cable. You may also use the INSERT jack as a pre-EQ/pre-fader send
by plugging in a ¼" TS cable part way to the first click.
STEREO LINE IN
STEREO LINE IN
(4)
– Plug in a stereo source using two ¼" TS cables, or a single
line-level source using the left input jack only.
GAIN LINE
GAIN LINE
(5)
– Adjusts STEREO LINE IN sensitivity, also known as “gain
setting.”
GAIN MIC
GAIN MIC
(6)
– Adjusts MIC input sensitivity, also known as “gain setting.”
CLIP
(7)
– Lights when preamp begins to overload.
PAN/BAL
(8)
– Adjusts the left-to-right positioning of the channel in
the stereo field.
HIGH
HIGH
(9)
– Adjusts frequencies above 10 kHz by +- 15 dB.
MID
(10)
– Adjusts frequencies peaking at 700 Hz by +- 15 dB.
LOW
(11)
– Adjusts frequencies below 50 Hz by +- 15 dB.
MON
(12)
– Adjusts the amount of signal sent to the MON SEND jack. This signal
is sent pre-fader.
FX
FX
(13)
– Adjusts the amount of signal sent to the FX SEND jack. This signal is sent
post-fader.
CHANNEL FADER
CHANNEL FADER
(14)
– Adjusts the channel volume in the main mix.
2-TRACK OUTPUT
(15)
– Connect to the inputs of recording device using
RCA cables.
2-TRACK INPUT
2-TRACK INPUT
(16)
– Connect to outputs of CD, tape or MP3 player using RCA
or ¼" cables.
PHONES
PHONES
(17)
– Connect a pair of headphones with a ¼" TRS plug.
MAIN OUTPUT
(18)
– Connect to the inputs of a power amp or powered speakers
using ¼" TS cables.
FX SEND
FX SEND
(19)
– Connect to the input of an external effects device using a
¼" TS cable.
MON SEND
MON SEND
(20)
– Connect to the input of a powered monitor or monitor power
amp using a ¼" TS cable.
VU CLIP
VU CLIP
(21)
– Lights when the MAIN OUTPUT signal begins to overload.
PHANTOM
(22)
– Sends 23V of power to the XLR MIC inputs for use with
condenser microphones. When used with batteries, 18V of power is supplied.
VU METER
VU METER
(23)
– Displays the MAIN OUTPUT signal level.
MON SEND
(24)
– Adjusts the output at the MON SEND jack.
FX SEND
(25)
– Adjusts the output at the FX SEND jack.
PHONES
(26)
– Adjusts the output at the PHONES jack.
MAIN FADER
(27)
– Adjusts the overall output of the mixer through the MAIN
OUTPUTS. It also affects the signal at the PHONES out and 2-TRACK OUTPUT.