Yamaha YSP-3050 Mode D'Emploi

Subwoofer

AUTO SETUP START

Will begin in 20sec

Please leave the room

**--------

[RETURN]:Cancel

AUTO SETUP

PREPARATION & CHECK

Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.

After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel

Measurement takes about 3min.

SHOW RESULT

MEASUREMENT COMPLETE

BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE

[ENTER]:Save set-up

[RETURN]:Do not save set-up

AUTO SETUP COMPLETE

Please remove the MIC from
the YSP and the listening
position.

VOLUME

MIN

MAX

CROSSOVER/

HIGH CUT

MIN

MAX

Carry out the AUTO SETUP to adjust the settings that best match your listening 
environment.

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. 

It is normal for loud test tones to be output 

during the AUTO SETUP procedure. 

Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.

Enjoy TV or DVD digital audio in surround sound.

For instructions on how to operate or set your TV or DVD player/recorder, refer to the owner’s manual supplied with each component.

Assemble the cardboard microphone stand.

Place the IntelliBeam microphone on top of cardboard microphone stand as shown below.

y Hint

y Hint

Continued from the front

1

Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC jack 
on the front panel.

2

Set the IntelliBeam microphone at your normal listening position.

Use the supplied cardboard microphone stand or a tripod to 

place the IntelliBeam microphone at the same height as your ears would

be when you are seated.

3

Press STANDBY/ON on the remote control.

The power of this unit turns on.

Before operations, insert batteries into the remote 

control (see page 24 in the Owner’s Manual).

If necessary, adjust the volume level of this unit.

If you have connected the subwoofer, set the 

volume and crossover/high cut frequency. Refer 

to the “Notes” on page 30 in the Owner’s Manual.

4

Set the operation mode selector to 
YSP.

This unit switches to the YSP operation mode.

7

Press ENTER to start the AUTO 
SETUP procedure, and then leave 
the room within 10 seconds.

The following screen appears on the TV. Leave the room within 

10 seconds before the AUTO SETUP procedure starts.

The setup screen automatically changes during the AUTO 

SETUP procedure.

When the AUTO SETUP procedure is completed, the following 

screen appears on the TV.

If “ENVIRONMENT CHECK (FAILED) is displayed, see page 34 

in the Owner’s Manual and then run the procedure again.

• The result may differ depending on the environment.

• If any error occurs, the corresponding error message appears 

on the screen. In this case, see “Error messages for AUTO 

SETUP” on page 35 in the Owner’s Manual and then follow 

the instructions. To start the AUTO SETUP procedure once 

again, press RETURN.

11

Press and hold AUTO SETUP for 
more than 2 seconds.

The menu screen appears on the TV.

If the menu screen does not appear, check the OSD video pin 

cable (see the connection example on the front page).

8

Prepare to leave the room.

The best setting may not be done if you are in the room.

Prepare to leave the room in 10 seconds after pressing ENTER 

in step 11.

• When leaving the room, bring this guide with you.

• Wait outside the room during the AUTO SETUP procedure.

• The AUTO SETUP procedure takes 

about 3 minutes.

• To cancel the AUTO SETUP procedure after it is started, 

press RETURN.

10

Disconnect the IntelliBeam 
microphone.

The AUTO SETUP has completed. Keep the IntelliBeam 

microphone in a safe place.

The settings are automatically saved in the system memory.

13

Check the following points.

• Is the microphone placed on an imaginary center line drawn 

from this unit?

• Is the microphone placed within 1 m (3.3 ft) upper or lower 

from the center height of this unit?

• Is the microphone placed more than 1.8 m (6.0 ft) from the 

front of this unit?

• Is your listening room kept as quiet as possible?

9

Press ENTER.

The following screen appears on the TV for 2 seconds and then 

the menu screen disappears from the TV.

12

Select the DVD video input on 
your TV.

1

Check the digital signal being output at this unit.

The input channel indicators (see page 8 in the Owner’s Manual) are lit in the front panel display, and they 

switch according to the channel composition of the corresponding input source. 

If the sound is output from your 

TV speakers, mute the volume on your TV. 

For details about digital audio input signals, see page 58 in the 

Owner’s Manual.

4

Press one of the beam mode buttons on the remote control to 
select the desired beam mode.

Select one of the six beam modes that best matches the current input source of this unit.

For further information on the beam modes, see pages 56, 57, 62, 63 and 64 in the Owner’s Manual.

6

Press VOLUME +/- on the remote control to adjust the 
volume level of this unit.

5

Select the TV channel using the 
remote control supplied with your TV.

Mute the volume on the TV.

1

Set the operation mode selector to 
YSP.

This unit switches to the YSP operation mode.

2

Set the operation mode selector to 
YSP.

This unit switches to the YSP operation mode.

2

1) Press DVD on the remote 

control of this unit.

This unit switches to the DVD playback mode.

2)  Play back 

the supplied demonstration 

DVD 

on the DVD player/recorder.

3

Press TV on the remote control of 
this unit.

This unit switches to the TV playback mode.

3

Turn on the power of your TV.

5

Select the appropriate video input 
on your TV.

If the OSD video pin cable is connected to the video input 1 on 

the TV as shown in the connection example 1, switch the video 

input to “1”.

6

IntelliBeam microphone (supplied)

Cardboard microphone stand (supplied)

Place the IntelliBeam microphone on the 
extended center line of this unit and 1.8 m (6.0 ft) 
or more away from it. Also, make sure place the 
IntelliBeam microphone within 1 m (3.3 ft) upper 
or lower from the center height of this unit.

IntelliBeam 
microphone

Center height of 

this unit

IntelliBeam 
microphone

Cardboard 

microphone stand

More than 1.8 m (6.0 ft)

Upper bound 
position of the 
microphone

Within 1 m (3.3 ft)

Within 1 m (3.3 ft)

Listening 
position

Lower bound position 
of the microphone

Center line

Cardboard

microphone

stand

Enjoying DVDs in surround sound

Enjoying TV in surround sound

Input channel indicators

To fine-tune the listening environment parameters manually or make advanced settings for speaker positions, sound 

beams, etc., see “MANUAL SETUP” on page 74 in the Owner’s Manual.