ONKYO TX-NR929 Manuel D’Utilisation

BLUETOOTH button and indicator

Wi-Fi indicator

Playing an Audio from Bluetooth enabled Device
You can enjoy music files on Bluetooth-enabled devices such as smart phones or digital music players wirelessly. (Bluetooth-
enabled devices must support A2DP protocol)

• When you play music files on your Bluetooth-enabled device, you need to establish paring only for the first time.
• Look for the following operation procedure of the Bluetooth-enabled device as an input source before establishing pairing. “Procedure 

to turn the Bluetooth setting ON” “Procedure to connect the Bluetooth-enabled device to other components”.

■

Put the AV receiver to pairing mode
When you press 

BLUETOOTH on the front panel of the AV receiver, Bluetooth indicator flashes and the AV receiver is 

put to pairing mode.

• When establishing pairing with other Bluetooth-enabled device, press and hold down 

BLUETOOTH on the AV receiver until 

the Bluetooth indicator flashes.

The AV receiver can save up to ten pairing information.

Connecting to Bluetooth-enabled device
Connect the AV receiver to the Bluetooth-enabled device from a close distance (approx. 1 m) while the indicator on the 
AV receiver is flashing. 
When a model name of the AV receiver is displayed on the screen of Bluetooth-enabled device, select it. After a short 
while, pairing will be completed.

• When asked for a password on the Bluetooth-enabled device, enter “0000”.

If you connect the AV receiver to your Bluetooth-enabled device with the AV receiver ON, input selector on the AV receiver is 
automatically switched to Bluetooth position. Play back the music files in this Bluetooth position status.

• It may take 20 seconds or more from turning the AV receiver ON to completing the connection because of the start of  

Bluetooth function.

• Audio is not output from the AV receiver if audio volume on the Bluetooth-enabled device is set small.

■

For further information, see 

“

Playback

”

 in the Instruction Manual.

You can enjoy listening to Internet radio or files on a server (DLNA) through Wi-Fi (Wireless LAN) network. You need to perform 
the wireless LAN setup to connect the AV receiver to a wireless device such as a wireless router.

There are two types of setting, “Automatic” and “Manual”. If your wireless LAN router has a “WPS 
button” (*), automatic setup is available. If not, make the setting manually. If the router does not 
support WPS, take a note of a SSID and b Password (secret key) on the label of the router. 
Manual setting is available regardless of the “WPS button” on the router.

(*) The “WPS button” is a standard of Wi-Fi Alliance. The name of the button may differ depending on 

the router maker.

■

Rear Panel

When the AV receiver is connected 
to the network by wireless, adjust the 
position of the antenna.

Connect the AV receiver to your TV with HDMI and display the setup screen on the TV. Use a supplied remote controller for the 
setting. Press 

RECEIVER before using the remote controller. Use e/r or q/w in the center to select items on the screen, and 

press 

ENTER to confirm. Press RETURN to return to the previous screen.  

For further information, see “Remote Controller”. (→Page 8)

●

Initial Setup function is launched upon first-time use. To perform Initial Setup, move your cursor and click on “

Wireless” in “Network 

Connection”, press ENTER, select “Yes” on the next screen, and press ENTER. (*2)

●

This is a setting using Setup Menu (Home Menu). Display “

Wireless setup” menu by performing the following procedure which contains 

five steps.
1.

  Press Receiver followed by Home on the remote controller.

2.

  Select “Setup” on the screen, and press ENTER.

3.

  Select “Hardware Setup”, and press ENTER.

4.

  Select “Network (*1)”, and press ENTER.

5.

  Select “Network Connection”, move your cursor and click on “Wireless”, and press ENTER. (*2)

(*1)

  When “Network” is grayed out, please wait until it becomes operable after the communication is completed.

(*2)

  The reaction may be slow. Please wait for a short while.

●

Select “

Push Button Configuration (Linksys E/EA Router)” (Connection to Linksys E/EA Router) or “Push Button Configuration (Other 

Routers)”, and press ENTER for North American models.
Select “

Push Button Configuration (Select from Router)” , and press ENTER for excluding North American models.

●

Select “

Search Wireless Network”, and press ENTER.

Select “

Push Button” (*) and press 

ENTER. Press “WPS button” on the 
wireless LAN router, select “

OK” on the TV 

screen, and press 

ENTER.

(*) If you select “

PIN Code”, PIN code setting is 

available. Use this setting in case WPS button is in 
the hard location to press, etc. In PIN code setting, 
register the displayed eight-digit PIN code with 
the wireless LAN router. For registration, see the 
instruction manual provided with the wireless  
LAN router.

Select SSID of your wireless LAN router 
from the list of SSID displayed on the 
screen, and press 

ENTER. Either of the 

following options is automatically displayed 
in conjunction with the wireless  
router setting.
WEP method

1. Select “

Default key ID”, and press 

ENTER.

2. Select “

1” on the next screen. (If you 

change WEP key on the router side, 
select that number.)

3. Select “

Password” on the next screen, 

and press 

ENTER.

4. Enter the Password (*) by using a key 

board displayed on the screen, select 
“

OK”, and press ENTER.

5. Select “

OK” on the next screen, and 

press 

ENTER.

(*)  Pressing Shift switches between 

uppercase and lowercase.

1. Select “

Password”, and press ENTER.

2. Enter the Password (*) by using a key 

board displayed on the screen, select 
“

OK”, and press ENTER.

3. Select “

OK” on the next screen, and 

press 

ENTER.

(*)  Pressing Shift switches between 

uppercase and lowercase.

No encryption
You do not need to set the default key ID 
nor Password. Select “

OK” on the screen, 

and press 

ENTER. Select “OK” on the next 

screen again, and press 

ENTER.

Connection is started, and Wi-Fi indicator flashes on the left of the AV receiver display. When connected successfully, Wi-Fi indicator lights. 
If the indicator does not light, the connection was not made successfully. Make settings above again. Try the manual setting if the automatic 
setting does not work.

Press 

HOME on the remote controller, select “Network Service” on the next screen. You can enjoy various types of Internet functions. For 

further information, see “Playback” in the Instruction Manual.

If the settings or operations of Wi-Fi or Bluetooth do not work, see separate volume, “Wi-Fi & Bluetooth Troubleshooting”.

■