ONKYO TX-DS989 Manuel D’Utilisation
24
IR IN
MAIN
ZONE 2
ZONE 2
OUT
BACK
L
L
R
BACK
R
R
L
CAUTION:SPEAKER IMPEDANCE
6 OHMS MIN. PER EACH
SPEAKER TERMINAL
SPEAKER TERMINAL
SURROUND (SURR)
SPEAKERS
AC OUTLETS
AC 120V 60Hz
SWITCHED
TOTAL 120W 1A MAX.
SWITCHED
TOTAL 120W 1A MAX.
AC
INLET
INLET
AM
ANT.
FM
ANT.
75
75
MULTI
CHANNEL
INPUT
CHANNEL
INPUT
RS
232
GND
C
FRONT
AMP
IN
R
L
SURR
BACK
SURR
PRE OUT
SUB
WOOFER
FRONT
SPEAKERS
SPEAKERS
CENTER
SPEAKER
SPEAKER
CAUTION:
SPEAKER IMPEDANCE
6 OHMS MIN. PER EACH
SPEAKER TERMINAL
SPEAKER TERMINAL
1
2
MODEL NO.
TX-DS989
AV RECEIVER
VIDEO
S VIDEO
DVD
VIDEO
5
VIDEO
4
VIDEO
3
MONITOR
OUT
VIDEO
1
VIDEO
2
OUT
IN
IN
IN
IN
IN
IN
OUT
R
L
VIDEO
S VIDEO
C D
TAPE
2
TAPE
1
I N
I N
I N
I N
OUT
OUT
L
R
PHONO
3
2
1
3
2
5
4
1
DIGITAL
OUTPUT
(COAXIAL)
AC-3
RF
RF
DIGITAL
INPUT
(COAXIAL)
DIGITAL
OUTPUT
(OPTICAL)
DIGITAL
INPUT
(OPTICAL)
INPUT 2
P
B
P
R
Y
INPUT 3
P
B
P
R
Y
OUTPUT
P
B
P
R
Y
COMPONENT
VIDEO
INPUT 1
P
B
P
R
Y
1
2
R
L
IR IN
MAIN
ZONE 2
ZONE 2
OUT
R
L
OUT
HOME THEATER CONTROLLER
RC-390M
Connecting to the IR IN ZONE 2 input
Outline
The IR IN ZONE 2 input allows you to control the TX-DS989
from the remote zone (Zone 2) with the remote controller even
though the remote zone is physically separated. The diagram
below shows how to make the proper connections for the remote
zone.
from the remote zone (Zone 2) with the remote controller even
though the remote zone is physically separated. The diagram
below shows how to make the proper connections for the remote
zone.
The following equipment (sold separately) is essential for
operation from the remote zone:
operation from the remote zone:
• Onkyo’s Multi-Room System kits (IR Remote Controller
Extension System), or
• Multiroom A/V distribution and control systems from Niles
®
and Xantech
®
to name a few
Make connection as shown below. Do not plug the equipment into
the power source until the connection is complete.
the power source until the connection is complete.
Connecting the main and remote zones
The ZONE 2 terminal is a constant output. Connect to the LINE
input of the amplifier (CD, tape, etc.). Adjust the volume with the
amplifier connected to the ZONE 2 terminal.
input of the amplifier (CD, tape, etc.). Adjust the volume with the
amplifier connected to the ZONE 2 terminal.
1. Connect the TX-DS989 to the amplifier for the
remote zone.
2. Connect the remote zone speaker cables to the
speaker terminals on the amplifier.
3. Connect the TX-DS989 to the monitor for the
remote zone.
4. Install the connecting block in the main zone
and connect it to the IR IN ZONE 2 input at the
TX-DS989.
TX-DS989.
5. Install the remote sensor in the remote zone
and connect it to the connecting block in the
main zone.
main zone.
Main zone
Remote zone (Zone 2)
Zone 2
speaker
Zone 2
speaker
Zone 2 monitor
or projector
Zone 2 amplifier
Remote sensor
(Multi-Room System kit)
(Multi-Room System kit)
Remote controller
Connecting block
(Multi-Room System kit)
(Multi-Room System kit)
TX-DS989
Connection example for Onkyo’s Multi-room System kit
Audio connection cable
Video and S-video connection cables
Mini plug cable
Power supply
Wall outlet
Signal flow
LINE IN