ONKYO HT-RC260 Manuel D’Utilisation

En

■

*1*2

`

–50 to 0 to +50

With this setting you can adjust saturation. “–50” is 
the weakest color. “+50” is the strongest color.

*1

This procedure can also be performed on the remote controller 
by using the Video menu (

*2

Press CLR if you want to reset to the default value.

You can assign a default listening mode to each input 
source that will be selected automatically when you select 
each input source. For example, you can set the default lis-
tening mode to be used with Dolby Digital input signals. 
You can select other listening modes during playback, but 
the mode specified here will be resumed once the AV 
receiver has been set to Standby.

■

Analog / PCM
With this setting, you can specify the listening mode to 
be used when an analog (CD, TV, LD, VHS, MD, turn-
table, radio, cassette, cable, satellite, etc.) or PCM digi-
tal (CD, DVD, etc.) audio signal is played.

■

Mono/Multiplex Source
With this setting, you can specify the listening mode to 
be used when a mono digital audio signal is played 
(DVD, etc.).

■

2ch Source
With this setting, you can specify the default listening 
mode for 2-channel (2/0) stereo sources in a digital for-
mat, such as Dolby Digital or DTS.

■

Dolby D/Dolby D +/TrueHD
With this setting, you can specify the listening mode to 
be used when a Dolby Digital or Dolby Digital Plus for-
mat digital audio signal is played (DVD, etc.). Specifies 
the default listening mode for Dolby TrueHD sources, 
such as Blu-ray or HD DVD (input via HDMI).

■

DTS/DTS-ES/DTS-HD
With this setting, you can specify the listening mode to 
be used when a DTS or DTS-HD High Resolution for-
mat digital audio signal is played (DVD, LD, CD, etc.). 
Specifies the default listening mode for DTS-HD Mas-
ter Audio sources, such as Blu-ray or HD DVD (input 
via HDMI).

■

Other Multich Source
With this setting, you can specify the default listening 
mode for multichannel PCM sources from HDMI IN 
such as DVD-Audio, and DSD multichannel sources 
such as Super Audio CD.

■

`

Off, 30 to 79

With this setting, you can limit the maximum vol-
ume.
To disable this setting, select “Off”.

■

`

, Min, 1 to 79 or Max

With this preference, you can specify the volume set-
ting to be used each time the AV receiver is turned 
on.

To use the same volume level that was used when the AV 
receiver was turned off, select “Last”.
The “Power On Volume” cannot be set higher than the 
“Maximum Volume” setting.

■

`

–12dB to 0dB to +12dB

With this preference, you can specify the headphone 
volume relative to the main volume. This is useful if 
there’s a volume difference between your speakers 
and your headphones.

■

On Screen Display
This preference determines whether operation details 
are displayed on-screen when an AV receiver function is 
adjusted.

`

On:

Displayed.

`

Off:

Not displayed.

Even when “On” is selected, operation details may not be 
output if the input source is connected to an HDMI IN.

1

q/w to select the input source that you want to 

The following menu appears.

For TUNER input selector only “Analog” will be 
available.

• If you connect an input component (such as UP-A1 series 

Dock that seated iPod) to the UNIVERSAL PORT jack, 
you can assign only listening modes for the analog sound 
to PORT selector.

2

q/w to select the signal format that you want 

e/r to select a listening mode.

Only listening modes that can be used with each 
input signal format can be selected (

29 to 32).

The “Last Valid” option means that the listening 
mode selected last will be used.