ONKYO HT-RC180 Manuel D’Utilisation
51
If the impedance of any speaker is 4 ohms or more but
less than 6, set the minimum speaker impedance to 4
ohms.
If you’ve connected your front speakers to the FRONT
L/R and SURR BACK/ZONE 2 L/R terminal posts for
bi-amping, you must change the “Speakers Type(Front)”
setting. For hookup information, see “Bi-amping the
Front Speakers” on page 21.
less than 6, set the minimum speaker impedance to 4
ohms.
If you’ve connected your front speakers to the FRONT
L/R and SURR BACK/ZONE 2 L/R terminal posts for
bi-amping, you must change the “Speakers Type(Front)”
setting. For hookup information, see “Bi-amping the
Front Speakers” on page 21.
Notes:
• When bi-amping is used, the AV receiver is able to
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the
volume.
Powered Zone 2/3
Note:
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
This procedure can also be performed on the AV receiver
by using its [SETUP] button, arrow buttons, and
[ENTER] button.
Speaker Settings
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q]/[w] but-
tons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
3
Use the Up and Down [
q]/[w] but-
tons to select “1. Speaker Set-
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
If you change these settings, you must run
Audyssey MultEQ
Audyssey MultEQ
®
Room Correction and Speaker
Setup again (see page 54).
2. Speaker
Setup
1. Speaker
Settings
2. Speaker
Configuration
3. Speaker
Distance
4. Level
Calibration
5. Equalizer
Settings
6. THX Audio Setup
2–1. Speaker
Settings
Speaker Impedance
Speakers Type(Front)
Powered Zone2
Powered Zone3
Speakers Type(Front)
Powered Zone2
Powered Zone3
6ohms
Normal
Not Act
Not Act
Not Act
4
Use the Up and Down [
q]/[w] but-
tons to select “Speaker Imped-
ance”, and then use the Left and
Right [
ance”, and then use the Left and
Right [
e]/[r] buttons to select:
4ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
less than 6.
6ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
16 ohms.
5
Use the Up and Down [
q]/[w] but-
tons to select “Speakers
Type(Front)”, and then use the
Left and Right [
Type(Front)”, and then use the
Left and Right [
e]/[r] buttons to
select:
Normal: Select this if you’ve con-
nected your front speakers
normally.
normally.
Bi-Amp: Select this if you’ve con-
nected your front speakers
for bi-amped operation.
for bi-amped operation.
Note:
Powered Zone2/3 cannot be used if
“Speakers Type(Front)” is set to
“Bi-Amp”.
Powered Zone2/3 cannot be used if
“Speakers Type(Front)” is set to
“Bi-Amp”.
6
Press the [SETUP] button.
The setup menu closes.
The setup menu closes.
TX-NR807_En.book Page 51 Tuesday, July 28, 2009 12:00 PM