Emerson EM529 Fascicule

NOTE: When the [Power] switch is set to the ON position for 

the first time, the headset will be in Pairing Mode (the 

indicator light will be flashing RED and BLUE alternately), 

please refer to “Easy Pairing”.

 

• To turn ON, set the [Power] switch to the ON position (green).

The blue indicator light will flash intermittently.

 

• To turn OFF, slide the [Power] switch to the OFF position (red). 

The indicator light will flash RED before the headset shuts 

off.

• To answer a call, press and release the [Call] button or press 

the answer key on your mobile phone.

• To end a call, press and release the [Call] button or press the 

end key on your mobile phone.

During an incoming call press and HOLD the [Call] button 

for 3 seconds or until you hear a confirmation beep.

Making a call 

Dial the number and press the send button on your mobile 

phone, the call is automatically transferred to the headset.

(Dependent on your phone supporting this feature)

Press the [Call] button twice. The last number called will be 

redialed.

To adjust the in-call volume, press the [Volume Up] or [Volume 

Down] button.

NOTE: You may also adjust the volume from your mobile phone’s 

volume control.

Press the [Volume Up] and the [Volume Down] button 

simultaneously until you hear a beep, repeat to unmute the call.

For added comfort and noise suppression, 3 silicone cushions 

are included with the headset. Choose the silicone cushion (S) 

(M) (L) which fits most comfortably in your ear and insert it on 

the headset as shown in the diagram below.

You may wear the headset with or without the provided earhook. 

If you choose to use the earhook, connect it to the headset as 

shown in the diagram below.

NOTE: For the best audio quality, always wear the headset on 

the same side of your body as your mobile phone.

1. Go to the PS3 main menu, scroll to and select “Settings”.
2. Scroll to and select “Accessory Settings”.
3. Scroll to and select “Manage Bluetooth Devices”.
4. The menu will ask: “The Bluetooth device has not been 
    registered. Do you want to register it?”, then select “YES”.

1. Put the headset into pairing mode. (See “Manual Pairing”)
2. Select “Start Scanning” from the PS3 menu.
3. Once the PS3 has discovered the headset, the screen will read 
     “Select the Bluetooth device to register”, then select “EM529”
4. The PS3 will ask for a passkey. Enter “0000” then select “OK”. Now 
     press [O] (the PS3 circle button) to get back to the previous menu.

5. Scroll to and select “Audio Device Settings” to change the 
     “Input Device” to “EM529”.

NOTE: “Input Device” is the microphone, and determines the 

method of how others will hear you speak. By default, 
the “Output Device” will now switch to “EM529”.
 “Output Device” is the audio, and determines how you 
will hear the PS3 audio and others speaking. 

To test the connection, speak into the headset and you will see 
the bars above the “Microphone Level” moving, if not, repeat the 
pairing process.

Press “OK” to confirm the new settings. You are now ready to use 
the headset with your PS3 Entertainment System. If you would like 
to hear the PS3 audio through your TV or Audio System, scroll to 
“Output Device” and switch to “System Default Device”. 
 
For further assistance with Bluetooth settings on your PS3 please 
refer to your PS3 instruction manual.

Distributed by Southern Telecom Inc. Brooklyn, NY 11232

© 2011 Southern Telecom Inc. All rights reserved. 

Emerson and the G-Clef logo are registered trademarks of 

Emerson Radio Corp. Parsippany, New Jersey USA. 

The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. 

SONY PlayStatiion® & PS3™ are either trademarks or registered 

trademarks of SONY.

All other trademarks are trademarks of their respective owners.

In the unlikely event that this product is defective, or does 

not perform properly, you may within one (1) year from your 

original date of purchase return it to the authorized service 

center for repair or exchange.

Your product will be repaired or replaced, at our option, for the same 

or similar model of equal value if examination by the service center 

determines this product is defective.  Products received damaged 

as a result of shipping will require you to file a claim with the carrier.

This warranty does not cover damage resulting from accident, 

misuse, abuse, improper installation or operation, lack of reasonable 

care, and unauthorized modification. This warranty is voided in 

the event any unauthorized person opens, alters or repairs this 

product. All products being returned to the authorized service 

center for repair must be suitably packaged.

• THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY

APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES,  

EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE 

HEREBY DISCLAIMED. NO VERBAL OR WRITTEN  INFORMATION 

GIVEN BY SOUTHERN TELECOM INC. IT’S AGENTS, OR EMPLOYEES 

SHALL CREATE A GUARANTY OR IN ANY WAY INCREASE THE 

SCOPE OF THIS WARRANTY.

• REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY

IS THE EXCLUSIVE REMEDY OF THE CONSUMER. SOUTHERN 

TELECOM INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR 

CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS 

PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS 

OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER 

OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED 

BY THE LAWS OF THE STATE OF NEW YORK. EXCEPT TO THE 

EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED 

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO 

THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.

Some states do not allow the exclusion nor limitation of incidental 

or consequential damages, or limitations on how long an implied 

warranty lasts so the above limitations or exclusions may not apply 

to you. This warranty gives you specific legal rights, and you 

also may have other rights that vary from state to state.

Should you have any questions or problems concerning this 

product, please contact our customer service department at:

This equipment has been tested and found to comply with the 

requirements for a Class B digital device under Part 15 of the 

Federal Communications Commission (FCC) rules. These 

requirements are intended to provide reasonable protection 

against harmful interference in a residential installation. This 

equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, 

there is no guarantee that interference will not occur in a particular 

installation. If this equipment does cause harmful interference to 

radio or television reception, which can be determined by turning 

the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different 

   from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this equipment not  

expressly approved by the party responsible for compliance 

could void the user’s authority to operate the equipment.

Operation is subject to the following two conditions: (1) This 

device may not cause interference and (2) This device must 

accept any interference, including interference that may 

cause undesired operation of the device.

The term “IC:” before the certification/registration number 

only signifies that registration was performed based on a 

Declaration of Conformity indicating that Industry Canada 

technical specifications were met. It does not imply that 

Industry Canada approved the equipment.

• Try adjusting the volume by using the  [Volume Up] or 

   [Volume Down]  button on the headset; make sure the 

   volume on your mobile phone is turned up as well. 

• For the best audio quality, always wear the headset on the same 

side of the body as your mobile phone.

• Check that the battery is charged enough.

• Try turning the headset OFF, and then turning it ON again.

• Many mobile phones have an auto reconnect option when first 

attempting to reconnect to a newly paired Bluetooth device. 

Make sure you accept this option, so that  the headset  

automatically reconnects to your mobile phone; check the user 

guide of your mobile phone for more information regarding 

this option.

• Try unpairing the headset from your phone, and repeat the 

  pairing procedure.

• Make sure that you fully charged the headset before pairing.

• Keep the headset and mobile phone within 3 feet of each 

other during the pairing process.

• Check that your phone’s Bluetooth feature is turned ON.

• Try removing the battery from your mobile phone for 5 minutes. 

Place the battery back in the phone, power it on, and retry the 

pairing process (see “Manual Pairing”). 

• Try repeating the pairing process, see “Manual pairing.”

• Make sure the headset is turned on before beginning the 

pairing process (the headset is in pairing mode when you 

turn it on for the first time).

• If you are not pairing for the first time or for manual pairing, 

press and HOLD the [Call] button until the indicator light 

flashes RED and BLUE alternately.

S M L

Although most people associate Bluetooth headsets with 

mobile phones, there are many other  products today which 

include Bluetooth® wireless technology.

In most cases the pairing process is similar to pairing with a 

mobile phone which is explained in detail in the "Manual 

Pairing" section.

Below, the pairing procedure with the SONY Playsation3 is 

explained, to pair with other devices it is best to refer to the 

device's Owner's Manual.

Power ON

(Green)

Power OFF

(Red)

Right ear

Left ear

Answer/end a call

Press twice to redial

Press simultaneously

to mute and unmute