TOA Electronics VM-2120 Manuel D’Utilisation
12
6.2. Remote Microphone RM-200M
[Top]
1. Gooseneck microphone
A unidirectional microphone.
2. Name label
Insert the label (not thicker than 0.2 mm) indicating
the name of each panel control and indicator. (See
p. 60 "NAME LABEL PREPARATION.")
the name of each panel control and indicator. (See
p. 60 "NAME LABEL PREPARATION.")
3. Power indicator (POWER)
Lights green when the power is supplied to the
unit.
unit.
4. Failure indicator (FAULT)
Lights yellow when the VM (VM-2120/-2240)
amplifier's front panel-mounted failure indicator
lights.
Flashes yellow when a communications failure
occurs between the unit and the VM amplifier.
amplifier's front panel-mounted failure indicator
lights.
Flashes yellow when a communications failure
occurs between the unit and the VM amplifier.
5. Emergency indicator (EMERGENCY)
Lights red when the VM amplifier is in Emergency
mode. (See p. 21.)
mode. (See p. 21.)
6. Emergency broadcast switch (EMERGENCY)
Press this switch after opening the security cover
when making the Emergency Broadcast.
when making the Emergency Broadcast.
7. Groups 1&2 indicator (GROUP 1, 2)
Lights green when the corresponding group is
selected with the key.
selected with the key.
8. Groups 1&2 broadcast key (GROUP 1, 2)
Press this key to make the Group Broadcast
(Broadcast to preprogrammed multiple zones).
(See p. 51 "BROADCAST GROUP/ZONE
SETTING.")
(Broadcast to preprogrammed multiple zones).
(See p. 51 "BROADCAST GROUP/ZONE
SETTING.")
9. All-zone indicator (ALL-ZONE)
Lights green when the All-Zone Broadcast is
selected with the key.
selected with the key.
10. All-zone broadcast key (ALL-ZONE)
Press this key to make the All-Zone Broadcast.
11. Zone selector key (ZONE 1 – 5)
Selects the desired broadcast zones (Zones 1 – 5).
12. Zone indicator (ZONE 1 – 5)
Lights green when the corresponding broadcast
zone (Zones 1 – 5) is selected.
zone (Zones 1 – 5) is selected.
13. Message (MESSAGE 1 – 5)/zone (ZONE 6 –
10) selector key
(1) When only a single VM-2120 or VM-2240
amplifier is connected
Selects broadcast messages 1 – 5 pre-recorded
on the optional Voice Announcement Board EV-
200.
Selects broadcast messages 1 – 5 pre-recorded
on the optional Voice Announcement Board EV-
200.
(2) When two VM-2120 or VM-2240 amplifiers are
connected
Selects broadcast zones 6 – 10.
Selects broadcast zones 6 – 10.
14. Message (MESSAGE 1 – 5)/zone (ZONE 6 –
10) indicator
Lights green when the corresponding Message
(Zone) Selector Key is pressed.
Lights green when the corresponding Message
(Zone) Selector Key is pressed.
15. Busy indicator (BUSY)
Flashes orange or green when other connected
sound source unit is in use.
sound source unit is in use.
Orange: The RM-200M cannot operate.
Green: The RM-200M can interrupt the busy
Green: The RM-200M can interrupt the busy
unit.
16. In-use indicator (IN-USE)
Lights green when the RM-200M is in use.
17. Talk key (TALK)
Either of the following two operating methods can
be selected. (See p.50 "Remote Microphone's
Function Switches.")
be selected. (See p.50 "Remote Microphone's
Function Switches.")
(1) Press-to-talk system
Announcements can be made from the
microphone while the key is pressed, and are
terminated when released.
microphone while the key is pressed, and are
terminated when released.
(2) Talk lock system
One-touch depression locks the key and permits
announcements to be made from the
microphone. Press the key again to terminate the
announcement.
announcements to be made from the
microphone. Press the key again to terminate the
announcement.
Note
In the Emergency Broadcast, the Talk key
operates in the "press-to-talk" system even if set
to the "Talk lock system."
In the Emergency Broadcast, the Talk key
operates in the "press-to-talk" system even if set
to the "Talk lock system."
1
2
2
3
8
6
7
4
5
10
13
14
12
11
16
15
17
9