JAI CV-M536 Manuel D’Utilisation
- 17 -
CV-M536/538/539
7.3. Jumper Settings
Caution on Jumper Setting.
Before making any mode or jumper setting turn the power OFF.
Jumpers for mode setting are found on the boards PK8054 & PK8057.
The following modes are available with jumper setting:
Input/Output Mode of HD/VD signal. (HD/VD input is factory setting)
Edge Pre-select Mode. (Factory setting)
Pulse Width Control Mode
Start/Stop Trigger Mode
Long Time Exposure Mode
Edge Pre-select Mode. (Factory setting)
Pulse Width Control Mode
Start/Stop Trigger Mode
Long Time Exposure Mode
Set the jumpers according to the list below in 7.3.1. and 7.3.2.
The jumper positions are shown in “7.4.1. Board 8054 Side B” and “7.4.2. Board 8057 Side A”.
Switch SW2 on PK8057 is shown in “7.2. SW2 on PK8057 Board”.
The jumper positions are shown in “7.4.1. Board 8054 Side B” and “7.4.2. Board 8057 Side A”.
Switch SW2 on PK8057 is shown in “7.2. SW2 on PK8057 Board”.
Jumper
HD/VD in/out
External trigger modes
Remarks
Ext.
HD/VD
input *)
Int.
HD/VD
output
Edge pre-
select
Pulse
width
control
Start/
stop
trigger
Long time
expose
JP1
Short
Open
Short
Short
Short
Short
HD input /output. Factory set input
HD input /output. Factory set input
HD input /output. Factory set input
JP2
Open
Short
Open
Open
Open
Open
JP3
Short
Open
Short
Short
Short
Short
VD input /output. Factory set input
VD input /output. Factory set input
VD input /output. Factory set input
JP4
Open
Short
Open
Open
Open
Open
JP5
Short
Short
Short
Short
Short
Short
JP6
Open
Open
Open
Open
Open
Short
Long time integration
JP7
Short
Short
Short
Short
Open
Short
JP8
Open
Open
Open
Open
Short
Open
JP9
Open
Open
Open
Open
Short
Open
JP10
Open
Open
Open
Open
Short
Open
JP11
Open
-
-
-
-
-
Pixel clock out. Factory set OPEN
JP12
Short
Short
Short
Open
Short
Short
Pulse width
SW2-1
ON
-
ON
ON
ON
ON
HD in 75 Ohm term. Factory set ON
SW2-2
ON
-
ON
ON
ON
ON
VD in 75 Ohm term. Factory set ON
Jumper
HD/VD in/out
External trigger modes
Remarks
Ext.
HD/VD
input *)
Int.
HD/VD
output
Edge pre-
select
Pulse
width
width
control
Start/
stop
trigger
Long time
expose
R127
Short
Short
Short
Short
Open
Short
Factory set SHORT
7.3.1. Jumper on PK8054 Board
*) Factory Setting
7.3.2. Jumper on PK8057 Board
*) Factory Setting
7.3.3. Pixel Clock Output
To use pixel clock output (TTL level: 4.0 V), make the jumper JP11 on PK8057 board shorted-circuited. The
jumper position is shown in “7.4.1. Board PK8057 Side A”.
Pixel clock pulse will be output from pin no.9 of 12-pin multi-connector.
To use pixel clock output (TTL level: 4.0 V), make the jumper JP11 on PK8057 board shorted-circuited. The
jumper position is shown in “7.4.1. Board PK8057 Side A”.
Pixel clock pulse will be output from pin no.9 of 12-pin multi-connector.
Caution for Pixel Clock Output.
When the pixel clock is enabled, it may cause interference with external equipment if it not properly
shielded.
shielded.