JAI CV-A33CL Manuel D’Utilisation
CV-A33CL
- 20 -
7.3. CV-A33CL command list
Command Name
Format
Parameter
Remarks
A – General settings and useful commands
EB
EB
Echo Back
EB=[Param.]<CR><LF>
0=Echo off
1=Echo on
Off at power up
ST
Camera Status request
ST?<CR><LF>
Actual setting
HP
Online Help request
HP?<CR><LF>
Command list
VN
Firmware version
VN?<CR><LF>
3 letter version
ID
Camera ID request
ID?<CR><LF>
10 characters
MD
Model Name request
MD?<CR><LF>
≤ 10 characters
UD
User ID (Free text)
TR=[Param.]<CR><LF>
User can save and load free text
≤ 16 characters
B – Video Output
BA
Output bit allocation
BA=[Param.]<CR><LF>
0=10 bit
1=8 bit
Camera Link
C – Timing and shutter related commands
WS
WS
Windows Scan
WS=[Param.]<CR><LF>
0=full frame
1=windows scan
WX
X Scan start coordinate
WX=[Param.]<CR><LF>
0-657
Start pixel #
WY
Y Scan start coordinate
WY=[Param.]<CR><LF>
0-490
Start line#
WW
X Scan size width
WW=[Param.]<CR><LF>
2-659
Window width
WH
Y Scan size height
WH=[Param.]<CR><LF>
3 – 493
Window height
AT
Auto Trigger
AT=[Param.]<CR><LF>
3-493
*)
Wind. 3H to 493H
Wind. 3H to 493H
TR
Trigger mode
TR=[Param.]<CR><LF>
0=normal
2=Pulse width
2=Pulse width
1=Edge pre-sel
3=Auto Trigger
3=Auto Trigger
SM
Shutter mode
SM=[Param.]<CR><LF>
0=Normal 1=Program.
exp
SH
Shutter speed
SH=[Param.]<CR><LF>
0=Off (1/120)
2=1/500
4=1/2000
6=1/10000
2=1/500
4=1/2000
6=1/10000
1=1/250
3=1/1000
5=1/5000
7=1/20000
3=1/1000
5=1/5000
7=1/20000
All 8 steps are
valid in normal
trigger mode.
valid in normal
trigger mode.
PE
Programmable expos.
PE=[Param.]<CR><LF>
2-493
Exp. 1H to 492H
H= 16.8µsec
H= 16.8µsec
D– Signals and polarity
LS
LVAL synchronous accum.
LS=[Param.]<CR><LF>
0= LVAL sync.
1=
LVAL a-sync.
*1) Only a-sync.
TI
Trigger Input
TI=[Param.]<CR><LF>
0= CamerLink
1= 12 pin Hiror
TP
Trigger polarity
TP=[Param.]<CR><LF>
0= active low
1= active high
*2)
E – Gain and analogue signals setting
BL
BL
Black level
BL=[Param.]<CR><LF>
0-31
(0=low 31=high)
GA
Gain level
GA=[Param.]<CR><LF>
1-11
(0=low 11=high)
CB
Calibration of CMOS sensor CB=0<CR><LF>
0 is the only allowed parameter
Will calibrate the
CMOS sensor
CMOS sensor
F – Saving and loading data in EEPROM
LD
LD
Load settings from camera
EEPROM
EEPROM
LD=[Param.]<CR><LF>
0=Factory data
2=User 2 area
2=User 2 area
1=User 1 area
Latest used data
default at power
up
default at power
up
SA
Save settings to camera
EEPROM
EEPROM
SA=[Param.]<CR><LF>
1=User 1 area
2=User 2 area
Parameter = 0 is
not allowed
not allowed
*)
Auto trigger window will always start from top. Max frame rate with AT=3. It is 2 LVAL exposure + 9 LVAL offset.
*1)
The command LS is found on the first cameras. Only LS=1 is will work correct.
*2)
If positive logic is used (TP=1), the first trigger pulse after power up will be ignored. TTL only.
!!
Do not try to use commands not shown in this list.