Land Pride AR2596 Manuel D’Utilisation
10
Section 2: Options & Accessories
AR2596 & AR2510 Pasture Aerators 325-127M
12/09/15
Section 2: Options & Accessories
Rear Hitch Assembly (Accessory)
Refer to Figure 2-1:
1.
Attach leveling hitch (#2) to axle frame (#1) with
1" x 2 3/4" clevis pin (#4). Secure clevis pin with
3/16" x 1 3/4" cotter pin (#5). Bend one or both legs of
cotter pin to keep pin from falling out.
1" x 2 3/4" clevis pin (#4). Secure clevis pin with
3/16" x 1 3/4" cotter pin (#5). Bend one or both legs of
cotter pin to keep pin from falling out.
2.
Attach ratchet jack (#8) to the Aerator frame (#3) and
leveling hitch (#2) with 1" x 3 3/16" clevis pins (#7)
and 3/16" hairpin cotters (#6).
leveling hitch (#2) with 1" x 3 3/16" clevis pins (#7)
and 3/16" hairpin cotters (#6).
3.
Operate ratchet jack lever (#9) until hitch is level.
Rear Hitch Assembly
Figure 2-1
Concrete Weights (Optional)
Refer to Figure 2-2:
!
DANGER
Concrete blocks weight 740 lbs. each. Stay clear of them while
lifting them into place. Hands and fingers can easily become
pinched by the blocks or the blocks could shift suddenly or fall
causing serious bodily injury or death.
lifting them into place. Hands and fingers can easily become
pinched by the blocks or the blocks could shift suddenly or fall
causing serious bodily injury or death.
Mounting 2 Concrete Blocks
1.
Position concrete blocks (#1 & #3) onto the platform
ends. Make sure they are against the square tubes
on the ends and resting fully on the platform floor.
ends. Make sure they are against the square tubes
on the ends and resting fully on the platform floor.
2.
Place a spacer or spacers between the blocks to
keep then from shifting to one side. (Spacer(s)
provided by customer)
keep then from shifting to one side. (Spacer(s)
provided by customer)
30063
IMPORTANT: Use equipment capable of lifting a
minimum of 800 lbs. Lift one concrete block at a time
using lifting rods “B” to raise and lower the blocks
onto the platform frame.
minimum of 800 lbs. Lift one concrete block at a time
using lifting rods “B” to raise and lower the blocks
onto the platform frame.
NOTE: Remove SMV sign (#4) from its mounting
socket to prevent hitting the sign while installing the
concrete blocks. Replace SMV sign after the blocks
are installed.
socket to prevent hitting the sign while installing the
concrete blocks. Replace SMV sign after the blocks
are installed.
Mounting 3 Concrete Blocks
1.
Position concrete block (#1) onto the platform against
the left end. Make sure it is against the square tube
on that end and is resting fully on the platform floor.
the left end. Make sure it is against the square tube
on that end and is resting fully on the platform floor.
2.
Position the middle concrete block (#2) centered on
the platform frame.
the platform frame.
•
AR2596: The center block should be approximately
3 3/8" from the first block and resting fully on the
platform.
3 3/8" from the first block and resting fully on the
platform.
•
AR2510: The center block should be approximately
15 3/8" from the first block and resting fully on the
platform.
15 3/8" from the first block and resting fully on the
platform.
3.
Position concrete block (#3) onto the platform against
the right end. Make sure it is against the square tube
on that end and is resting fully on the platform floor.
the right end. Make sure it is against the square tube
on that end and is resting fully on the platform floor.
4.
Place spacers between the blocks to keep them from
shifting to one side. (Spacers provided by customer)
shifting to one side. (Spacers provided by customer)
Mounting 4 Concrete Blocks
Instructions For AR2510 Aerator Only
1.
Position concrete block (#1) onto the platform against
the left end. Make sure it is against the square tube
on that end and is resting fully on the platform floor.
the left end. Make sure it is against the square tube
on that end and is resting fully on the platform floor.
2.
Position the second concrete block (#2)
approximately 4" from the first block and resting fully
on the platform.
approximately 4" from the first block and resting fully
on the platform.
3.
Position the third concrete block (#4 not shown)
approximately 4" from the second block and resting
fully on the platform
approximately 4" from the second block and resting
fully on the platform
4.
Position the fourth concrete block (#3) onto the
platform against the right end. Make sure it is against
the square tube on that end and is resting fully on the
platform floor.
platform against the right end. Make sure it is against
the square tube on that end and is resting fully on the
platform floor.
5.
Place spacers between the blocks to keep them from
shifting to one side. (Spacers provided by customer)
shifting to one side. (Spacers provided by customer)
Concrete Weight Assembly (AR2596 Shown)
Figure 2-2
30064