CyClone 360 Manuel D’Utilisation
Controls
The following instructions are for Octal Mode only
Table below list the function of each channel and the functions of the RED, GREEN and BLUE
dimmer buttons.
dimmer buttons.
Q Select
RED UP/DN
GREEN UP/DN
BLUE UP/DN
Q1
Cluster 1 RED
Cluster 1 GREEN
Cluster 1 BLUE
Q2
Cluster 2 RED
Cluster 2 GREEN
Cluster 2 BLUE
Q3
Cluster 3 RED
Cluster 3 GREEN
Cluster 3 BLUE
Q4
Cluster 4 RED
Cluster 4 GREEN
Cluster 4 BLUE
Q5
Cluster 5 RED
Cluster 5 GREEN
Cluster 5 BLUE
Q6
Cluster 6 RED
Cluster 6 GREEN
Cluster 6 BLUE
Q7
Cluster 7 RED
Cluster 7 GREEN
Cluster 7 BLUE
Q8
Cluster 8 RED
Cluster 8 GREEN
Cluster 8 BLUE
Q9
Fade Time
Follow Time
Reserved for future use
Q10
Fade or Flash
Pattern
Pattern Direction
Effects Defi nitions
Fade Time: The Time the scene takes to fade from scene to scene.
Follow Time: The time between scenes.
Fade or Flash: Sets the Cyclone to fade or fl ash.
Pattren: Sets one of 8 preset patterns.
Pattern Direction: Sets the pattern direction (Foward or Reverse)
Follow Time: The time between scenes.
Fade or Flash: Sets the Cyclone to fade or fl ash.
Pattren: Sets one of 8 preset patterns.
Pattern Direction: Sets the pattern direction (Foward or Reverse)
Effects
The Cyclone360 effects are controlled using 2 channel buttons and the RGB setting of each channel. Each of the
effects have a value from 0 to 100 as displayed on the CM-T10-PRO-Enhanced display. We will cover each of the
effects and the how the value will affect the Cyclone360. For any effects to appear we must fi rst set the 8 clusters. For
this example we will set clusters 1 through 7 to RED and Cluster 8 to BLUE.
The Cyclone360 effects are controlled using 2 channel buttons and the RGB setting of each channel. Each of the
effects have a value from 0 to 100 as displayed on the CM-T10-PRO-Enhanced display. We will cover each of the
effects and the how the value will affect the Cyclone360. For any effects to appear we must fi rst set the 8 clusters. For
this example we will set clusters 1 through 7 to RED and Cluster 8 to BLUE.
Step 1: Press Q1 and RED UP until the display read 100. Cluster 1 on the Cyclone360 should be on.
Step 2: Repeat step 1 for Q2 through Q7.
Step 3: Press Q8 and press BLUE UP until display read 100.
Step 2: Repeat step 1 for Q2 through Q7.
Step 3: Press Q8 and press BLUE UP until display read 100.
The Cyclone360 should now have 1 BLUE cluster and the other 7 should be RED.
To activate the effects the Fade Time (Q10 RED) must be greater than 0.
Note: Fade time values are reversed from our ColorRoll Technology. 0 is OFF, 1 is Slow and 100 is Fast.
Activate the effects by pressing the RED UP button. For this example we will set it to 100 so press the RED UP button
until the display reads 100 then do the same for the Follow Time by pressing GREEN UP until the display reads 100.
The Cyclone360 should now be RED with a GREEN Cluster circling.
until the display reads 100 then do the same for the Follow Time by pressing GREEN UP until the display reads 100.
The Cyclone360 should now be RED with a GREEN Cluster circling.
Continue.....
3