Scag Power Equipment STT61V-31KB-DF Manuel D’Utilisation
25
R
Section 6
Actuate the steering control levers forward and
6.
reverse several times and return them to the neutral
position.
position.
Check that the drive wheels remained in neutral and
7.
readjust if necessary.
Check that the steering control levers hit the stop
8.
before the pumps reach full stroke. Adjust as
needed.
needed.
TRACKING ADJUSTMENT
CAUTION
Stop the engine and remove the key from the
ignition before making any adjustments. Wait
for all moving parts to come to a complete stop
before beginning work.
ignition before making any adjustments. Wait
for all moving parts to come to a complete stop
before beginning work.
CAUTION
The engine and drive unit can get hot during
operation causing burn injuries. Allow engine
and drive components to cool before making any
adjustments.
operation causing burn injuries. Allow engine
and drive components to cool before making any
adjustments.
- NOTe -
Before proceeding with this adjustment, be sure
that the caster wheels turn plus pivot freely and
that the tire pressure in the drive wheels is correct.
If the tire pressure is not correct, the machine will
pull to the side with the lower pressure.
that the caster wheels turn plus pivot freely and
that the tire pressure in the drive wheels is correct.
If the tire pressure is not correct, the machine will
pull to the side with the lower pressure.
If at full speed the mower pulls right, it is an
1.
indication that the left wheel is turning faster than
the right wheel. To adjust this condition, proceed as
follows:
the right wheel. To adjust this condition, proceed as
follows:
A. Stop the machine and place the steering control
levers in the neutral position. Loosen the lock nuts
securing the ball joints at each end of the LH steering
control rod. Rotate the control rod to lengthen the rod
and tighten the lock nuts. This will cause the control
rod to stroke the LH pump less, slowing down the LH
wheel. (See Figure 6-4, page 24)
levers in the neutral position. Loosen the lock nuts
securing the ball joints at each end of the LH steering
control rod. Rotate the control rod to lengthen the rod
and tighten the lock nuts. This will cause the control
rod to stroke the LH pump less, slowing down the LH
wheel. (See Figure 6-4, page 24)
- NOTe -
If after making the adjustment as outlined in step
1A, the machine creeps forward or backward, the
neutral adjustment must be made as described
on page 24.
1A, the machine creeps forward or backward, the
neutral adjustment must be made as described
on page 24.
If at full speed the mower pulls left, it is an indication
2.
that the right wheel is turning faster than the left
wheel. To adjust this condition, proceed as follows:
wheel. To adjust this condition, proceed as follows:
A. Stop the machine and place the steering control
levers in the neutral position. Loosen the lock nuts
securing the ball joints at each end of the RH steering
control rod. Rotate the control rod to lengthen the rod
and tighten the lock nuts. This will cause the control
rod to stroke the RH pump less, slowing down the RH
wheel. (See Figure 6-3, page 24)
levers in the neutral position. Loosen the lock nuts
securing the ball joints at each end of the RH steering
control rod. Rotate the control rod to lengthen the rod
and tighten the lock nuts. This will cause the control
rod to stroke the RH pump less, slowing down the RH
wheel. (See Figure 6-3, page 24)
- NOTe -
If after making the adjustment as outlined in step
2A, the machine creeps forward or backward, the
neutral adjustment must be made as described
on page 24.
2A, the machine creeps forward or backward, the
neutral adjustment must be made as described
on page 24.
THROTTLE CONTROL AND CHOKE
6.3
ADJUSTMENTS
ADJUSTMENTS
These adjustments must be performed by your Scag dealer
to ensure proper and efficient running of the engine. Should
either need adjustment, contact your authorized Scag
service center.
to ensure proper and efficient running of the engine. Should
either need adjustment, contact your authorized Scag
service center.
BELT ADJUSTMENT
6.4
WARNING
Before removing any guards, shut the engine off
and remove the ignition key.
and remove the ignition key.
All drive belts and cutter deck belts are spring loaded and
self-tensioning. The springs should be checked periodically
for proper alignment and wear.
self-tensioning. The springs should be checked periodically
for proper alignment and wear.