Troy-Bilt 772C0748 Manuel D’Utilisation
15
IMPORTANT: Mowing in reverse is not recommended.
WARNING:
Use extreme caution while
operating the tractor in the REVERSE
CAUTION MODE. Always look down and
behind before and while backing. Do not
operate the tractor when children or others are
around. Stop the tractor immediately if
someone enters the area.
CAUTION MODE. Always look down and
behind before and while backing. Do not
operate the tractor when children or others are
around. Stop the tractor immediately if
someone enters the area.
To use the REVERSE CAUTION MODE:
IMPORTANT:
The operator MUST be seated in the
tractor seat.
1.
Start the engine as previously instructed in this
Operator’s Manual.
Operator’s Manual.
2.
Turn the key from the NORMAL MOWING (Green)
position to the REVERSE CAUTION MODE
(Yellow) position of the key switch module. See
Figure 8.
position to the REVERSE CAUTION MODE
(Yellow) position of the key switch module. See
Figure 8.
3.
Depress the REVERSE PUSH BUTTON (Orange,
Triangular Button) at the top, right corner of the key
switch module. The red indicator light at the top, left
corner of the key switch module will be ON while
activated. See Figure 8.
Triangular Button) at the top, right corner of the key
switch module. The red indicator light at the top, left
corner of the key switch module will be ON while
activated. See Figure 8.
4.
Once activated (indicator light ON), the tractor can
be driven in reverse with the cutting blades (PTO)
engaged.
be driven in reverse with the cutting blades (PTO)
engaged.
5.
Always look down and behind before and while
backing to make sure no children are around.
backing to make sure no children are around.
6.
After resuming forward motion, return the key to the
NORMAL MOWING position.
NORMAL MOWING position.
IMPORTANT:
The REVERSE CAUTION MODE will
remain activated until:
a. The key is placed in either the NORMAL
MOWING position or STOP position.
b. The operator leaves the seat (Models with
Electric PTO ONLY).
c.
The operator engages the parking brake by
fully depressing the brake pedal and holding
it down while gently pushing the parking
brake button inward (Models with Manual
PTO ONLY).
fully depressing the brake pedal and holding
it down while gently pushing the parking
brake button inward (Models with Manual
PTO ONLY).
SETTING THE CUTTING HEIGHT
Select the height position of the cutting deck by placing
the deck lift lever in any of the six different cutting height
notches on the right side of the fender. Then adjust the
deck wheels so that they are between ¼-inch and ½-
inch above the ground when the tractor is on a smooth,
flat surface such as a driveway.
the deck lift lever in any of the six different cutting height
notches on the right side of the fender. Then adjust the
deck wheels so that they are between ¼-inch and ½-
inch above the ground when the tractor is on a smooth,
flat surface such as a driveway.
WARNING:
Keep hands and feet away
from the discharge opening of the cutting
deck.
deck.
Figure 8
NOTE:
The deck wheels are an anti-scalp feature of
the deck and are not designed to support the weight of
the cutting deck.
the cutting deck.
Refer to the ADJUSTMENTS section of this manual for
more detailed instructions regarding various deck
adjustments.
more detailed instructions regarding various deck
adjustments.
STARTING THE ENGINE
WARNING:
Do not operate the tractor if
the interlock system is malfunctioning. This
system was designed for your safety and
protection.
system was designed for your safety and
protection.
NOTE:
Refer to the TRACTOR SET-UP section of this
manual for Gasoline and Oil fill-up instructions.
•
Insert the tractor key into the ignition switch.
•
Place the PTO knob (or lever) in the disengaged
(Blade Stop) position.
(Blade Stop) position.
•
Engage the tractor’s parking brake.
•
Place the throttle control in the FAST (rabbit)
position.
position.
•
Pull the choke control outward.
•
Turn the ignition key clockwise to the START
position. After the engine starts, release the key. It
will return to the NORMAL MOWING position.
position. After the engine starts, release the key. It
will return to the NORMAL MOWING position.
IMPORTANT:
Do NOT hold the key in the START
position for longer than ten seconds at a time. Doing so
may cause damage to your engine’s electric starter.
may cause damage to your engine’s electric starter.
NOTE:
If starting problems are encountered, refer to
the TROUBLESHOOTING section of this manual.
•
After the engine starts, deactivate the choke
control.
control.
NOTE:
Do NOT leave the choke control on while
operating the tractor. Doing so will result in a "rich" fuel
mixture and cause the engine to run poorly.
mixture and cause the engine to run poorly.
Stop
Position
Start
Position
Indicator
Light
Reverse
Push
Button
Reverse
Caution Mode
Position