Troy-Bilt N779Pony Manuel D’Utilisation
17
SECTION 6: MAKING ADJUSTMENTS
WARNING:
Never attempt to make any
adjustments while the engine is running,
except where specified in the operator’s
manual.
except where specified in the operator’s
manual.
Leveling the Deck
NOTE:
Check the tractor’s tire pressure before
performing any deck leveling adjustments. Refer to
Tires on page 21 for information regarding tire pressure.
Tires on page 21 for information regarding tire pressure.
Front To Rear
The front of the cutting deck is supported by a stabilizer
bar that can adjusted to level the deck from front to rear.
The front of the deck should be between 1/4-inch and
3/8-inch lower than the rear of the deck. Adjust if
necessary as follows:
bar that can adjusted to level the deck from front to rear.
The front of the deck should be between 1/4-inch and
3/8-inch lower than the rear of the deck. Adjust if
necessary as follows:
•
With the tractor parked on a firm, level surface,
place the deck lift lever in the top notch (highest
position) and rotate the blade nearest the discharge
chute so that it is parallel with the tractor.
place the deck lift lever in the top notch (highest
position) and rotate the blade nearest the discharge
chute so that it is parallel with the tractor.
•
Measure the distance from the front of the blade tip
to the ground and the rear of the blade tip to the
ground.
to the ground and the rear of the blade tip to the
ground.
•
The first measurement taken should be between
1/4" and 3/8" less than the second measurement.
Determine the approximate distance necessary for
proper adjustment and proceed, if necessary.
1/4" and 3/8" less than the second measurement.
Determine the approximate distance necessary for
proper adjustment and proceed, if necessary.
•
Locate the jam nut and lock nut found on the front
side of the stabilizer bracket. See Figure 10. After
loosening the jam nut:
Tighten the lock nut to raise the front of the deck;
Loosen the lock nut to lower the front of the deck.
side of the stabilizer bracket. See Figure 10. After
loosening the jam nut:
Tighten the lock nut to raise the front of the deck;
Loosen the lock nut to lower the front of the deck.
Figure 9
•
Retighten the jam nut loosened earlier after proper
adjustment is achieved.
adjustment is achieved.
Side to Side
If the cutting deck appears to be mowing unevenly, a
side to side adjustment can be performed. Adjust if
necessary as follows:
side to side adjustment can be performed. Adjust if
necessary as follows:
•
With the tractor parked on a firm, level surface,
place the deck lift lever in the top notch (highest
position) and rotate both blades so that they are
perpendicular with the tractor.
place the deck lift lever in the top notch (highest
position) and rotate both blades so that they are
perpendicular with the tractor.
•
Measure the distance from the outside of the left
blade tip to the ground and the distance from the
outside of the right blade tip to the ground. Both
measurements taken should be equal. If they’re
not, proceed to the next step.
blade tip to the ground and the distance from the
outside of the right blade tip to the ground. Both
measurements taken should be equal. If they’re
not, proceed to the next step.
•
Loosen, but do NOT remove, the hex screw on the
left deck hanger bracket. See Figure 10.
left deck hanger bracket. See Figure 10.
Figure 10
•
Balance the deck by using a wrench to turn the
adjustment gear (found immediately behind the hex
cap screw just loosened) clockwise/up or
counterclockwise/down.
adjustment gear (found immediately behind the hex
cap screw just loosened) clockwise/up or
counterclockwise/down.
•
The deck is properly balanced when both blade tip
measurements taken earlier are equal.
measurements taken earlier are equal.
•
Retighten the hex cap screw on the left deck
hanger bracket when proper adjustment is
achieved.
hanger bracket when proper adjustment is
achieved.
Adjustment Gear