Yard-Man 247.27019 Manuel D’Utilisation
13
SECTION 6: MAKING ADJUSTMENTS
WARNING: Do not at any time make any
adjustment to riding mower without first
stopping engine and disconnecting spark
plug wire.
adjustment to riding mower without first
stopping engine and disconnecting spark
plug wire.
Brake Pedal
During normal operation of the rider mower, the brake
is subject to wear and tear. Check the brake
periodically by carrying out the following test:
is subject to wear and tear. Check the brake
periodically by carrying out the following test:
•
Release the parking brake and place the rider
mower in neutral. Depress the brake pedal and try
to roll the rider mower. The tractor should not move.
If the tractor moves, adjust the brake.
mower in neutral. Depress the brake pedal and try
to roll the rider mower. The tractor should not move.
If the tractor moves, adjust the brake.
WARNING: Do not adjust the brake while
the engine is running. Be sure to block the
wheels of the rider mower before making
any adjustments on the brake cable.
the engine is running. Be sure to block the
wheels of the rider mower before making
any adjustments on the brake cable.
Adjustment to the brake pedal is made at the cable end.
See Figure 9 .
See Figure 9 .
•
Set the parking brake and turn ignition key off.
•
Shift the cutting height lever to the lowest position.
•
Pivot the hood assembly up and remove the
grasscatcher bag and the side-discharge chute or
the mulching plug from the mower.
grasscatcher bag and the side-discharge chute or
the mulching plug from the mower.
•
Disconnect wire from the spark plug.
•
Locate the brake cable on the right side under the
front housing. See Figure 9 .
front housing. See Figure 9 .
•
Using a pair of 1/2” wrenches, loosen the jam nuts
and back the cable out to tighten or thread inward
to loosen. See Figure 9 inset.
and back the cable out to tighten or thread inward
to loosen. See Figure 9 inset.
•
Retighten the jam nuts when proper tension is
reached.
reached.
•
Unlock the parking brake and repeat the test
described above. Readjust if necessary.
described above. Readjust if necessary.
“Go” Pedal
Adjustment to the "Go" Pedal is made at the cable end.
See Figure 9 .
See Figure 9 .
•
Set the parking brake and turn ignition key off.
•
Shift the cutting height lever to the lowest position.
•
Pivot the hood assembly up and remove the
grasscatcher bag and the side-discharge chute or
the mulching plug from the mower.
grasscatcher bag and the side-discharge chute or
the mulching plug from the mower.
•
Disconnect wire from the spark plug.
•
Locate the speed control cable under the front
housing. See Figure 9 .
housing. See Figure 9 .
•
Loosen the jam nuts and back the cable out to
tighten or thread inward to loosen as shown.
tighten or thread inward to loosen as shown.
•
Retighten the jam nuts when proper tension is
reached.
reached.
•
Reconnect the spark plug wire and pivot the hood
assembly down.
assembly down.
Cutting Height
The deck cutting height adjustment lever is located on
the hood assembly. For a representation of the cutting
height positions, refer to Figure 7.
the hood assembly. For a representation of the cutting
height positions, refer to Figure 7.
•
Pull the lever out of the slot and slide it upward or
downward to the desired cutting height.
downward to the desired cutting height.
•
Lower the cutting height to mow close to the
ground.
ground.
•
Raise the deck height to the highest position when
you ride on a sidewalk or a road.
you ride on a sidewalk or a road.
•
To mow tall or thick grass, move the cutting height
adjustment lever to the highest position and cut.
Then move the lever to a lower position and cut
again.
adjustment lever to the highest position and cut.
Then move the lever to a lower position and cut
again.
Figure 9
Speed Control
Cable
Cable
Brake
Cable
Cable
Cable*
Jam Nuts
Lock Washer
Frame
Tighten
Loosen
*Same type of adjustment on both cables
(only one shown here)
(only one shown here)