Husqvarna LTH125 Manuel D’Utilisation
9
ASSEMBLY
INSTALL MULCHER PLATE (See Figs.6 & 7)
•
Install two latch hooks to mulcher plate using screw,
washer, lock washer, and weld nut as shown.
washer, lock washer, and weld nut as shown.
NOTE: Pre-assemble weld nut to latch hook by inserting
weld nut from the top with hook pointing down.
weld nut from the top with hook pointing down.
•
Tighten hardware securely.
•
Raise and hold deflector shield in upright position.
•
Place front of mulcher plate over front of mower deck
opening and slide into place, as shown.
opening and slide into place, as shown.
•
Hook front latch into hole on front of mower deck.
•
Hook rear latch into hole on back of mower deck.
CAUTION: Do not remove discharge
guard from mower. Raise and hold
guard when attaching mulcher plate
and allow it to rest on plate while in
operation.
guard from mower. Raise and hold
guard when attaching mulcher plate
and allow it to rest on plate while in
operation.
TO CONVERT TO BAGGING OR
DISCHARGING
DISCHARGING
Simply remove mulcher plate and store in a safe place.
Your mower is now ready for discharging or installation of
optional grass catcher accessory.
Your mower is now ready for discharging or installation of
optional grass catcher accessory.
LATCH
HOOKS
HOOKS
FIG. 7
✓
CHECKLIST
BEFORE YOU OPERATE AND ENJOY YOUR NEW
TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE
THE BEST PERFORMANCE AND SATISFACTION FROM
THIS QUALITY PRODUCT.
TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE
THE BEST PERFORMANCE AND SATISFACTION FROM
THIS QUALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓
All assembly instructions have been completed.
✓
No remaining loose parts in carton.
✓
Battery is properly prepared and charged. (Minimum
1 hour at 6 amps).
1 hour at 6 amps).
✓
Seat is adjusted comfortably and tightened securely.
✓
All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
the tires were overinflated at the factory).
✓
Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
✓
Check mower and drive belts. Be sure they are routed
properly around pulleys and inside all belt keepers.
properly around pulleys and inside all belt keepers.
✓
Check wiring. See that all connections are still secure
and wires are properly clamped.
and wires are properly clamped.
✓
Before driving tractor, be sure freewheel control is in
drive position.
drive position.
WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
EXTRA ATTENTION TO THE FOLLOWING IMPORTANT
ITEMS:
✓
Engine oil is at proper level.
✓
Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
gasoline.
✓
Become familiar with all controls - their location and
function. Operate them before you start the engine.
function. Operate them before you start the engine.
✓
Be sure brake system is in safe operating condition.
✓
It is important to purge the transmission before operat-
ing your tractor for the first time. Follow proper starting
and transmission purging instructions (See "TO START
ENGINE" and "PURGE TRANSMISSION" in Opera-
tion section of this manual).
ing your tractor for the first time. Follow proper starting
and transmission purging instructions (See "TO START
ENGINE" and "PURGE TRANSMISSION" in Opera-
tion section of this manual).
WELD
NUT
NUT
LATCH
HOOK
HOOK
SCREW
WASHER
LOCK
WASHER
WASHER
WELD
NUT
NUT
LATCH
HOOK
HOOK
MULCHER
PLATE
PLATE
WASHER
SCREW
LOCK
WASHER
WASHER
WELD NUT
FROM THE TOP
FROM THE TOP
HOOK POINTS
DOWN
DOWN
FIG. 6
DEFLECTOR
SHIELD
SHIELD