Yard-Man 11B-106C401 Manuel D’Utilisation
11
•
Before reinstalling the blade and the blade adapter
to the unit, lubricate the engine crankshaft and the
inner surface of the blade adapter with light oil (or
engine oil). Lubricating the bolt holes, bolts and
inner surface of the nuts is also recommended.
to the unit, lubricate the engine crankshaft and the
inner surface of the blade adapter with light oil (or
engine oil). Lubricating the bolt holes, bolts and
inner surface of the nuts is also recommended.
To Reinstall Blade:
•
Be sure to install the blade with the side of the
blade marked “Bottom” (or with part number) facing
the ground when the mower is in the operating
position.
blade marked “Bottom” (or with part number) facing
the ground when the mower is in the operating
position.
•
Be certain the blade is aligned with and seated onto
the blade adapter flanges.
the blade adapter flanges.
•
Place blade bell support on blade. Make sure the
notches on the blade bell support are aligned with
the small hole in the blade.
notches on the blade bell support are aligned with
the small hole in the blade.
•
Replace hex bolt.
•
Tighten to torque: 450 in. lbs. min., 600 in. lbs. max.
•
To ensure safe operation of mower, check all nuts
and bolts periodically for correct torque.
and bolts periodically for correct torque.
Deck Maintenance
•
The underside of the mower deck should be
cleaned after each use to prevent a buildup of
grass clippings, leaves, dirt or other matter. If this
debris is allowed to accumulate, it will invite rust
and corrosion, and may prevent proper mulching.
cleaned after each use to prevent a buildup of
grass clippings, leaves, dirt or other matter. If this
debris is allowed to accumulate, it will invite rust
and corrosion, and may prevent proper mulching.
•
The deck may be cleaned by tilting the mower and
scraping clean with a suitable tool (make certain the
spark plug wire is disconnected).
scraping clean with a suitable tool (make certain the
spark plug wire is disconnected).
NOTE: We do not recommend the use of pressure
washers or garden hose to clean your unit. They may
cause damage to electric components, spindles,
pulleys, bearings or the engine. The use of water will
result in shortened life and reduce serviceability.
washers or garden hose to clean your unit. They may
cause damage to electric components, spindles,
pulleys, bearings or the engine. The use of water will
result in shortened life and reduce serviceability.
Engine Maintenance
•
Refer to the separate engine manual for all engine
maintenance instructions.
maintenance instructions.
•
Maintain ENGINE OIL as instructed in the engine
manual.
manual.
•
Service AIR CLEANER every 25 hours under
normal conditions. Clean every few hours under
extremely dusty conditions. Poor engine
performance and flooding usually indicates that the
air cleaner should be serviced. To service the air
cleaner, refer to the engine manual.
normal conditions. Clean every few hours under
extremely dusty conditions. Poor engine
performance and flooding usually indicates that the
air cleaner should be serviced. To service the air
cleaner, refer to the engine manual.
•
The SPARK PLUG should be cleaned and the gap
reset once a season. Spark plug replacement is
recommended at the start of each mowing season;
check engine manual for correct plug type and gap
specifications.
reset once a season. Spark plug replacement is
recommended at the start of each mowing season;
check engine manual for correct plug type and gap
specifications.
•
CLEAN the engine regularly with a cloth or brush.
Keep the cooling system (blower housing area)
cleaned to permit proper air circulation which is
essential to engine performance and life. Be certain
to remove all grass, dirt and combustible debris
from muffler area.
Keep the cooling system (blower housing area)
cleaned to permit proper air circulation which is
essential to engine performance and life. Be certain
to remove all grass, dirt and combustible debris
from muffler area.
SECTION 10: OFF-SEASON STORAGE
The following steps should be taken to prepare lawn
mower for storage.
mower for storage.
•
Clean and lubricate mower thoroughly as described
in the lubrication instructions.
in the lubrication instructions.
NOTE: We do not recommend the use of pressure
washers or garden hose to clean your unit. They may
cause damage to electric components, spindles,
pulleys, bearings or the engine. The use of water will
result in shortened life and reduce serviceability.
washers or garden hose to clean your unit. They may
cause damage to electric components, spindles,
pulleys, bearings or the engine. The use of water will
result in shortened life and reduce serviceability.
•
Refer to engine manual for correct engine storage
instructions.
instructions.
•
Coat mower’s cutting blade with chassis grease to
prevent rusting.
prevent rusting.
•
Store mower in a dry, clean area. Do not store next
to corrosive materials, such as fertilizer.
to corrosive materials, such as fertilizer.
NOTE: When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rust-proof the equipment. Using a light oil or
silicone, coat the equipment, especially cables and all
moving parts.
an unventilated or metal storage shed, care should be
taken to rust-proof the equipment. Using a light oil or
silicone, coat the equipment, especially cables and all
moving parts.