Wright Manufacturing 26980 Manuel D’Utilisation
2
Now try moving the hand control levers, one at a time, forward and backward. Check to see if the wheels
move forward and backward according to position of the levers. If not, service the hand control system. If
the wheels stop when the hand controls are in the neutral position, the parking brake should now be
applied.
move forward and backward according to position of the levers. If not, service the hand control system. If
the wheels stop when the hand controls are in the neutral position, the parking brake should now be
applied.
• Before testing the blade clutch/brake operation, make sure the area is clear and there is nothing vulnerable to
possible thrown objects from under the mower. No one should be near the mower deck or in its line of
discharge at this time or at any time. The discharge chute deflector should be in the down position. The
parking brake should now be applied. Move the engine throttle to ¾ speed setting.
discharge at this time or at any time. The discharge chute deflector should be in the down position. The
parking brake should now be applied. Move the engine throttle to ¾ speed setting.
• Place your feet firmly on the foot platform and turn on the blade clutch switch. Run blades for a minute or so.
Try engaging and disengaging the blades a few times about 10 seconds apart. If the blades do not start
and stop in a short amount of time, service the blade brake system. With the blades on, now try lifting your
feet off the foot platform to test the Operator Presence Control switch (OPC). The engine should die and
the blades should stop in several seconds. If not, service the OPC system. Try this a couple of times.
and stop in a short amount of time, service the blade brake system. With the blades on, now try lifting your
feet off the foot platform to test the Operator Presence Control switch (OPC). The engine should die and
the blades should stop in several seconds. If not, service the OPC system. Try this a couple of times.
• Disengage the blades, set the parking brake, shut off the engine and remove the mower from the stand(s).
• Drive the mower around on a level parking lot. It is recommended that the slower setting of the
Speed/Sensitivity Adjustment be used. (See further in this manual for information on Speed/Sensitivity
Adjustment.) Be sure that the mower drives in a straight line when both hand controls are held to the full
speed position which is up against the stationary control bar. If not, see further in this manual for
information on tracking adjustment.
Adjustment.) Be sure that the mower drives in a straight line when both hand controls are held to the full
speed position which is up against the stationary control bar. If not, see further in this manual for
information on tracking adjustment.
• As you drive the mower, listen for any unusual noises and test for irregular operation and adjust or service as
necessary. Next, go over the safety information and operating procedures in this manual with the customer.
Instruct the customer in proper operation and observe the customer during their initial operation on a level
parking lot. Make sure the customer is familiar and comfortable with the basic operation and use of the
mower.
Instruct the customer in proper operation and observe the customer during their initial operation on a level
parking lot. Make sure the customer is familiar and comfortable with the basic operation and use of the
mower.
• Dealer: Please fill out and follow the instruction on the Product Registration Form and have the customer fill out
his part of the form. After the Product Registration Card is filled out and signed by the customer and a
representative from your dealership, please send or fax it within 14 days to your Wright Commercial
Products Distributor according to the directions on the Card. Then give the customer his copy of the
registration form and then keep your copy and mail the remaining copies of the form to your Wright
Commercial Products Distributor. The limited warranty is not valid unless the mower is registered and all of
the above steps are taken. Remember, the purchaser is both your and our customer and his satisfaction is
very important. Thank you for supporting our products.
representative from your dealership, please send or fax it within 14 days to your Wright Commercial
Products Distributor according to the directions on the Card. Then give the customer his copy of the
registration form and then keep your copy and mail the remaining copies of the form to your Wright
Commercial Products Distributor. The limited warranty is not valid unless the mower is registered and all of
the above steps are taken. Remember, the purchaser is both your and our customer and his satisfaction is
very important. Thank you for supporting our products.
The mower is now ready for delivery to your customer.