Cal Spas 6300 Manuel D’Utilisation

Page 30 

2008 Portable Spa Owner’s Manual

 

LTR20081000, Rev. B

Cal  Spas™  All-Purpose  Cleaner  is  an 
essential  part  of  maintaining  your  spa’s 

finish.  Through  normal  use,  the  spa’s 

finish can accumulate dirt, oil, and calcium 
causing  a  rough  feel  and  unsightly  scum 
lines.  Cal  Spas™  All-Purpose  Cleaner 
is  a  low  detergent,  non-abrasive  cleaner 

specifically  formulated  to  clean  the  spa 

without damaging its acrylic finish.

The  most  effective  solution  to  minimize 
cleaning  time  is  prevention.  When  the 

following steps are followed, the spa’s finish will actually 
start to resist most of the elements that cause calcium 
build-up and make scum line clean up easier.

Spray Cal Spas™ Multi-Purpose Cleaner directly on 

to the spa’s finish.

Wipe clean with a clean soft cloth.

Repeat on heavily calcified areas.

Wipe  spa  thoroughly  with  a  wet  sponge,  rinsing 
often with a bucket of clean water.

Allow spa to dry completely.

Apply a coat of Cal Spas™ Fast Sheen to the spa’s 

entire finish with a soft towel or sponge.

Allow Fast Sheen to dry until white and powdery.

Buff clean with a soft cloth, rotating frequently.

Spray Cal Spas™ Multi-Purpose Cleaner directly to 

the spa’s finish.

Wipe clean with a clean soft cloth.

Wipe  spa  thoroughly  with  a  wet  sponge,  rinsing 
often in a bucket of clean water.

Cal  Spas™  Multi-Purpose  Cleaner  should  not  be 
sprayed  directly  into  the  spa  water.  Incorrect  usage  of 
this product will cause water clarity issues.

Cal  Spas™  Fast  Sheen  is  an  essential 

part  of  maintaining  your  spa’s  finish. 

Through  normal  use,  the  spa’s  finish 
can  accumulate  dirt,  oil,  and  calcium, 
causing a rough feel and unsightly scum 
lines. Cal Spas™ Fast Sheen is a non-oil 

1.

2.

3.

4.

5.

6.

7.

8.

1.

2.

3.

Remove the filter baskets and filters.
Drain  your  spa  completely  as  described  in  the 
instructions above.

Remove drain plugs from the front of the pumps.

Disconnect the unions from both sides of the pump.

Use a wet/dry vacuum to blow any remaining water 
out of the jets and equipment area.

Cover your spa with a good spa cover and an all-weather 
tarp to ensure that neither rain nor snow enters the spa.

Due  to  the  constant  punishment  your  spa  cover  and 
pillows  receive,  you  should  protect  them  by  applying 
Vinyl  and  Leather  Cleaner  as  part  of  your  monthly 
maintenance  plan.  Cal  Spas™  Vinyl  and  Leather 

Cleaner  is  specifically  designed  to  protect  spa  covers 
and pillows from chemical and ultraviolet light damage. It 
accomplishes this without leaving an oily residue behind 
that  is  normally  associated  with  common  automotive 
vinyl protectants.

Cal Spas™ Vinyl and Leather Cleaner 
should  be  used  sparingly.  Incorrect 
usage may cause water clarity issues.

Remove spa cover from spa.

Allow spa cover to dry completely.

Spray  Vinyl  and  Leather  Cleaner 
to cover evenly and wipe dry.

Allow spa cover to dry completely.

Reinstall cover on spa.

Wipe pillows dry with a soft cloth.

Carefully  spray  Vinyl  and  Leather  Cleaner  directly 
onto pillow.

Wipe pillows dry.

Allow pillows to dry completely.

Warning:  Do  not  use  automotive  vinyl  protectants  on 
spa covers or pillows. These products are generally oil-
based and will cause severe water clarity issues that are 

difficult to correct.

2.

3.

4.

5.

6.

1.

2.

3.

4.

5.

1.

2.

3.

4.