Roland VGA-3 Manuel D’Utilisation
13
Settings for the GK Pickup (GK Setup)
GK PHASE Setting
This matches the phase of the GK pickup's sound with the
sound from the guitar's pickup.
sound from the guitar's pickup.
* If the phases are not matched, the sound from each source will
interfere with each other when mixed, altering the tonal
qualities and volume levels.
qualities and volume levels.
1. Set the GK pickup’s select switch to “MIX.”
2. Rotate [GUITAR TYPE] to select
“HOLLOW” (GK PHASE).
3. While playing the sixth string, press MEMORY button
[1] or [2] to select the setting which does not diminish
the volume level in the low end.
the volume level in the low end.
GK S1/S2 Setting
This selects the functions for the GK pickup’s S1 and S2
buttons.
buttons.
1. Rotate [GUITAR TYPE] to select
“12 STRING/ELECTRIC” (GK S1/S2).
2. Press MEMORY button [1] , [2] , [3], or [4] to select the
functions for the S1 and S2 buttons.
GK SENS 6–1 Settings
This sets the GK pickup sensitivity for each string and
adjusts the volume balance between the strings.
adjusts the volume balance between the strings.
1. Set the GK pickup’s select switch to “SYNTH.”
2. Rotate [GUITAR TYPE] to select
“STANDARD” (GK SENS 6).
3. While playing the sixth string, press a MEMORY
button [1]–[10] to set the sensitivity for the sixth string.
The sensitivity increases the higher you set the value,
resulting in higher volume levels.
resulting in higher volume levels.
The PICKUP indicators show the level. The indicators
light from the bottom up in response to how strongly
you play the string.
light from the bottom up in response to how strongly
you play the string.
* Set this to a value such that the center (C) indicator lights, and
the upper (F) indicator flashes from time to time during the
most dynamic moments of a performance. Also, monitor the
actual sound to make sure it is not distorted.
most dynamic moments of a performance. Also, monitor the
actual sound to make sure it is not distorted.
fig.0040
4. Set the sensitivity for the fifth through first strings in
the same way.
5th String:
Rotate [GUITAR TYPE] to select
“12 STRING/ACOUSTIC” (GK SENS 5).
“12 STRING/ACOUSTIC” (GK SENS 5).
4th String:
Rotate [GUITAR TYPE] to select
“SYNTH LEAD” (GK SENS 4).
“SYNTH LEAD” (GK SENS 4).
3rd String:
Rotate [GUITAR TYPE] to select
“SYNTH PAD” (GK SENS 3).
“SYNTH PAD” (GK SENS 3).
2nd String: Rotate [GUITAR TYPE] to select
“SLOW GEAR” (GK SENS 2).
1st String:
Rotate [GUITAR TYPE] to select
“POLY OCTAVE” (GK SENS 1).
“POLY OCTAVE” (GK SENS 1).
* If you cannot attain a suitable level even when the value is set
to its maximum (10), check the installation of the GK pickup
(the clearance between the strings and the pickup).
(the clearance between the strings and the pickup).
* If any string produces a particularly loud sound, lower the
sensitivity for that string in order to minimize volume
differences between strings.
differences between strings.
Memory button
Setting
[1]
NORMAL
The phase will remain unchanged.
The phase will remain unchanged.
[2]
INVERSE
The phase will be inverted.
The phase will be inverted.
Memory button
Setting
[1]
PICKUP
Switching the pickup of COSM guitar
S1 button: R→C→F
S2 button: F→C→R
Switching the pickup of COSM guitar
S1 button: R→C→F
S2 button: F→C→R
[2]
PICKUP (REVERSE)
Switching the pickup of COSM guitar
S1 button: F→C→R
S2 button: R→C→F
Switching the pickup of COSM guitar
S1 button: F→C→R
S2 button: R→C→F
[3]
MANUAL/TUNER
S1 button:
Switching the Manual/Memory mode.
S2 button:
Switching the Tuner on/off.
S1 button:
Switching the Manual/Memory mode.
S2 button:
Switching the Tuner on/off.
[4]
MEMORY
▼/▲
S1 button: memory number down
S2 button: memory number up
S2 button: memory number up
Memory button
Setting
[1]–[10]
1–10
High
(Lower the SENS setting)
Correct
Low
(Raise the SENS setting)