Yamaha MOTIF XS7 Manuel D’Utilisation
Editing a Normal Voice
MOTIF XS Owner’s Manual
104
V
oice mode
Song mode
P
attern mode
Mixing mode
Master mode
Utility mode
File mode
P
erf
ormance
ormance
mode
Sampling
mode 1
Sampling
mode 2
Ref
erence
Controller settings—[F4] Ctrl Set
(Controller Set)
(Controller Set)
The controllers such as knobs on the front panel can be
used to change and adjust a variety of parameters for each
Voice—in real time, and simultaneously. For example,
keyboard aftertouch can be used to control vibrato and the
Modulation Wheel could be used to control tonal
brightness.
The function settings for all the controllers are referred to as
a “Controller Set,” and up to six Controller Sets can be
created for each Voice. The controller is referred to as
Source, and the controlled function is referred to as
Destination. From this display, you can determine the
Controller Sets.
used to change and adjust a variety of parameters for each
Voice—in real time, and simultaneously. For example,
keyboard aftertouch can be used to control vibrato and the
Modulation Wheel could be used to control tonal
brightness.
The function settings for all the controllers are referred to as
a “Controller Set,” and up to six Controller Sets can be
created for each Voice. The controller is referred to as
Source, and the controlled function is referred to as
Destination. From this display, you can determine the
Controller Sets.
n Depending on the selected parameter, the LIST icon is shown
at the tab menu corresponding to the [SF6] button. In this
condition, you can call up the list by pressing the [SF6] LIST
button, then select the desired item from the list. For details,
see page 82.
condition, you can call up the list by pressing the [SF6] LIST
button, then select the desired item from the list. For details,
see page 82.
1 Source*
Determines which panel controller is to be assigned and
used for the selected Set. You can also assign multiple
functions to a controller. You can set this parameter by
operating the desired controller while holding the [SF5]
Controller button.
used for the selected Set. You can also assign multiple
functions to a controller. You can set this parameter by
operating the desired controller while holding the [SF5]
Controller button.
Settings:
PitchBend
Indicates the built-in Pitch Bend wheel.
ModWheel
Indicates the built-in Modulation wheel.
AfterTch (Aftertouch)
Indicates the event generated when pressure is applied to a key after
the note is played.
the note is played.
FootCtrl1 (Foot Controller2)
FootCtrl2 (Foot Controller2)
FootCtrl2 (Foot Controller2)
Indicates the Foot Controller connected to each of the FOOT
CONTROLLER 1 and 2 jacks on the rear panel.
CONTROLLER 1 and 2 jacks on the rear panel.
FootSw (Footswitch)
Indicates the Footswitch connected to the FOOT SWITCH
ASSIGNABLE jack on the rear panel.
ASSIGNABLE jack on the rear panel.
Ribbon
Indicates the built-in Ribbon Controller.
Breath
Indicates the external controller which sends the control change
number assigned to the Breath Controller in the Utility mode
(page 264) to the MOTIF XS via MIDI.
number assigned to the Breath Controller in the Utility mode
(page 264) to the MOTIF XS via MIDI.
Assign1
Assign2
Assign2
Indicates the Knobs printed “ASSIGN 1” and “ASSIGN 2” with the
TONE 1 lamp turned on.
TONE 1 lamp turned on.
A. Func 1
A. Func 2
A. Func 2
Indicates the built-in ASSIGNABLE FUNCTION [1] and [2] buttons.
n You can determine the degree to which the Pitch Bend wheel
affects the Destination parameter (below) by setting the Pitch
Bend Range Upper (
Bend Range Upper (
4) and Pitch Bend Range Lower (5) in
2 Destination*
Determines the parameter that is controlled by the Source
controller (above). You can select a parameter for each
controller from the 67 parameters, such as volume, pitch
and LFO depth.
controller (above). You can select a parameter for each
controller from the 67 parameters, such as volume, pitch
and LFO depth.
Settings: Settings: Refer to the Control List in the separate Data List
booklet.
n Regarding “Insertion Effect A Parameter 1 – 16,” “Insertion
Effect B Parameter 1 – 16” and “Insertion Effect L Parameter 1
– 32” described in the Control List, the actual parameter
names of the selected Effect type are shown on the display. If
one of these names is shown, no function is assigned to that
parameter.
– 32” described in the Control List, the actual parameter
names of the selected Effect type are shown on the display. If
one of these names is shown, no function is assigned to that
parameter.
Setting examples of the Destination
Concerning *1 – *4, the following settings are necessary in
addition to the above setting.
addition to the above setting.
3 Depth*
Determines the degree to which the Source controller
affects the Destination parameter. For negative values, the
controller operation is reversed; maximum controller
settings produce minimum parameter changes.
affects the Destination parameter. For negative values, the
controller operation is reversed; maximum controller
settings produce minimum parameter changes.
Settings: -64 – +0 – +63
4 Element Switch*
Determines whether or not the selected controller affects
each individual element. This parameter is disabled when
the Destination (
each individual element. This parameter is disabled when
the Destination (
2) described above is set to a parameter
unrelated to the Voice Elements.
1
2
3
4
5
To control the volume:
Volume
To apply vibrato to the
Voice:
Voice:
Common LFO Depth 1 – 3
(C-LFO dpth1 – 3) *1
(C-LFO dpth1 – 3) *1
To change the pitch:
Element Pitch
(coarse tune) *2
(coarse tune) *2
To control the brightness of
the Voice:
the Voice:
Element Filter Frequency
(cutoff) *2
(cutoff) *2
To change the speed of the
Rotary Speaker:
Rotary Speaker:
Insertion A/B Parameter 1
(insA-prm1/insB-prm1) *3
(insA-prm1/insB-prm1) *3
To apply a wah pedal to the
Voice:
Voice:
Insertion A/B Parameter 1
(insA-prm1/insB-prm1) *4
(insA-prm1/insB-prm1) *4
*1 [F4] Com LFO
→ [SF1] Wave → Play Mode = loop
[F4] Com LFO
→ [SF2] Set → Control Dest = P mod
*2 [F3] Ctrl Set
→ Element Switch = on
*3 [F6] Effect
→ Insertion A/B Type = Rotary Speaker
[F6] Effect
→ Element Out = insA/insB
*4 [F6] Effect
→ Insertion A/B Type = Wah effect
[F6] Effect
→ Element Out = insA/insB