Behringer EG2080-RW/BK Manuel D’Utilisation
22
EUROGRAND EG2080-
RW/BK
Function:
E8.4
Value:
On, Off
Description:
Off
:
Save function for soft pedal settings is disabled
(default setting)
(default setting)
On
:
Save function for soft pedal settings is enabled
6.6.6 Restoring the factory default settings
Use the following procedure to recall the factory default settings.
ATTENTION: All saved parameters as well as the
music sequencer data will be lost during either
one of the following procedures.
music sequencer data will be lost during either
one of the following procedures.
1) Use the POWER switch to switch the instrument off (if not
already done).
2) Play and hold down the top C key on the keyboard, then
switch the EG2080 back on.
+
An alternative procedure is described below:
1) Use the POWER switch to switch the instrument off (if not
already done).
2) Press and hold down the TRACK 1 and TRACK 2 buttons,
then switch the EG2080 back on.
+
3) Let go of the TRACK buttons after about 5 seconds.
7. CONNECTION TO EXTERNAL
EQUIPMENT
The EG2080 provides a variety of connectors for connecting the
instrument to external devices.
instrument to external devices.
WARNING: Be sure that all devices are switched off
before you make any connection.
before you make any connection.
WARNING: NEVER connect the LINE IN connectors of
the EG2080 to its LINE OUT connectors. This will
cause a feedback loop producing high volume
levels which could damage both the instrument
and your hearing!
the EG2080 to its LINE OUT connectors. This will
cause a feedback loop producing high volume
levels which could damage both the instrument
and your hearing!
7.1 Connecting external sound sources
The EG2080 is equipped with a stereo LINE IN connector for
connecting external sound sources to your digital piano. These
signals are reproduced through the internal loudspeakers and
connected headphones. If you wish to practise with musical
accompaniment, you can use this input to connect a CD player or
drum computer. In the same way, you could connect an external
synthesizer or sound module and use its sound generator with
your instrument. An additional MIDI connection enables you to
play an external sound generator from the keyboard of the EG2080
(see chapter 7.3.1).
connecting external sound sources to your digital piano. These
signals are reproduced through the internal loudspeakers and
connected headphones. If you wish to practise with musical
accompaniment, you can use this input to connect a CD player or
drum computer. In the same way, you could connect an external
synthesizer or sound module and use its sound generator with
your instrument. An additional MIDI connection enables you to
play an external sound generator from the keyboard of the EG2080
(see chapter 7.3.1).
The following diagram shows a wiring example comprising the
EG2080 and a CD player. You need one or two cables fitted with
1/4" or cinch plugs (see chapter 10.1.3). As an alternative, you
can also use a cinch or 1/4" cable with an appropriate adapter
plug.
EG2080 and a CD player. You need one or two cables fitted with
1/4" or cinch plugs (see chapter 10.1.3). As an alternative, you
can also use a cinch or 1/4" cable with an appropriate adapter
plug.
Fig. 7.1: Connecting external signal sources
1) Connect the outputs of the CD player to the LINE IN
connectors of the EG2080.
For a mono connection use the LINE IN L (MONO)
connector on the EG2080.
connector on the EG2080.
7.2 Connection to external amplifiers and
recording equipment
The EG2080 is equipped with two LINE OUT connectors for
connecting the digital piano to external keyboard amplifiers, P.A.
systems or home stereo systems. For performances in larger
rooms (e.g. stages, hall) it can be necessary to use external
amplifiers.
connecting the digital piano to external keyboard amplifiers, P.A.
systems or home stereo systems. For performances in larger
rooms (e.g. stages, hall) it can be necessary to use external
amplifiers.
7. CONNECTION TO EXTERNAL EQUIPMENT