Korg 2E ii Manuel D’Utilisation

The output will not be sent to AUDIO OUT-

PUT (MAIN) L/MONO, R, or to (INDIVIDUAL) 1, 
2 (After passing through the master effects, it will be 
output from AUDIO OUTPUT (MAIN).) Select this 
when you wish to connect the output to the master 
effects in a series connection at the send levels spec-
ified by “MFX Send.”

3 “MFX Send” specifies the send level from each 

This is valid only if “BUS Select (All OSCs)” is set to 
L/R

 or Off.

If IFX is selected for “BUS Select (All OSCs),” the 
send level to the master effects is adjusted by the 
“Send 1 (MFX1)” and “Send 2 (MFX2)” parameters 
(PROG 7.1: Ed-InsertFX, Setup page) after the signal 
has passed through the insert effect.

1 Access the PROG 7.1: Ed-InsertFX, Setup page.

The Setup page displays the state of the routing and 
insert effect settings. In this page you can also make 
“BUS Select” settings. Use the [ ], [ ] cursor keys 
to select (All OSCs), and use the [INC]/[DEC] keys 
to make the setting.

2 In “Insert Effect,” select the desired insert effect.

You can use the Utility “Select by Category” to 
select effects from six categories.

3 In “On/Off,” turn the insert effect on/off.

If this is set to Off, the result will be the same as if 
00: No Effect

 is selected. The input sound will be 

output without change.

You can use the Utility “Copy Insert Effect” to 
copy effect settings from another program, etc.

4 Set the “Pan (CC#8),” “BUS Select,” “S1 (Send1 

“Pan (CC#8)”: Set the pan. This is valid only if “BUS 
Select” is set to L/R.
“BUS Select”: Specify the output destination. Nor-
mally you will set this to L/R. If you want to output 
the sound from AUDIO OUTPUT (INDIVIDUAL) 1 
and/or 2, set this to 1, 2, or 1/2.
“Send1 (MFX1),” “Send2 (MFX2)”: Set the send 
level to the master effects. For this example, set 
these to 127.

5 Move to the IFX page, and set the parameters of 

For details on the parameters of each effect, refer to 
PG p.168–.

The input level of the master effect is determined by 
the send level 1 and 2 settings (routing step 3, or 
insert effect step 4). If send levels 1 and 2 are 0, no 
master effects will be applied. Send level 1 is for MFX1, 
and send level 2 is for MFX2.

1 Select the PROG 7.2: Ed-MasterFX, Setup page.

2 In “Master Effect 1” and “Master Effect 2,” select 

The procedure is the same as for the insert effect. 
(

☞

step 1)

The input/output of the master effect is mono-on/
stereo-out. Even if you select a stereo-input type 
effect, the input will be monaural.

3 In “On/Off,” switch each master effect on/off.

If this is Off, the output of the master effect will be 
muted.

4 Specify the routing of master effects 1 and 2.

For details on the routing settings, refer to PG p.163.

5 In “Rtn (Return 1, 2),” adjust the output level of 

For each effect, the W value of “W/D” (Wet/Dry) 
is the effect output level. This is multiplied by the 
return value (“Rtn”=127 is x1.0) to determine the 
actual master effect output level.

6 Move to the MFX1 or MFX2 page, and set the 

For details on the parameters of each effect, refer to 
PG p.168–.

1 Use the stereo 3-band master EQ to make final 

Master EQ settings can be made in “Master EQ Gain 
[dB]” of the PROG 7.2: Ed-MasterFX, Setup page, or 
in the Master EQ page.
For details on master EQ parameters, refer to PG 
p.213.