Behringer DCX2496 Manuel D’Utilisation

ULTRADRIVE PRO DCX2496 User Manual

The POLARITY parameter determines whether the phase of an output signal 

is INVERTED or not (NORMAL)—just as if you had inverted the polarity of your 

speakers. Use the PHASE parameter to adjust the precise phase position at the 

upper X-OVER frequency of the currently selected output. This fine adjustment 

is necessary when two output signals are not perfectly displayed by 0° or 180° 

with regard to each other.

Fig. 4.42: Out 5 ➠ Delay

The DLY parameter in the top left corner of the display switches the DELAY 

function ON or OFF. With the LINK function you can couple several output 

DELAYS, so that you only have to adjust one DELAY for a whole stack of speakers. 

However, this applies to LONG DELAY values only. SHORT DELAY values 

can be adjusted separately and independently of the LINK function, and can 

be linked to each other in the SETUP menu (page 1/6), using the parameter 

OUT STEREO LINK. 
The parameters SHORT and LONG allow you to define the DELAY values of 

your choice. The setting range for the SHORT Delay is from 0 to 4,000 mm 

(= 0.00 to 11.64 ms) and the LONG Delay can be adjusted from 0.00 to 200.00 m 

(= 0.00 to 582.24 ms). 
With the LINK function activated, all LONG DELAY changes at one output are 

transferred to the corresponding output (L > M > H of one stereo side)—

irrespective of the selected output configuration (e.g. LMHLMH). 

When you have set all DELAY values for the outputs and then activated the LINK 

function for one of them, the LONG DELAY values are NOT transferred to the 

linked outputs. This happens only when you edit any parameters that change the 

values of the linked outputs proportionally. The current DELAY values are still not 

copied, but rather the linked output values follow the changes.
The output links are shown graphically, with the currently selected OUT channel 

displayed as an inverted loudspeaker, in the top right-hand corner of the display. 

Below are the DELAY times shown on a timeline.

Fig. 4.43: Mute ➠ Select

On this page, you can mute individual or all input/output channels. 

Use the parameters MUTE ALL OUTS and MUTE ALL INS to disable (OK) 

or de-mute (CANCEL) the inputs/outputs of the DCX2496 in one go. To mute 

or de-mute individual channels, please use the respective input/output 

buttons (e.g. OUT 2, IN A, SUM, etc.). The lower part of the display only shows 

the status of the channel and does not allow for any selection.

MUTE settings of any type can be made exclusively on this page. As soon as an 

input/output has been muted, the bottom red LED above the corresponding 

input/output button lights up.
Press MUTE again or select another menu to quit the MUTE menu. Pressing the 

IN or OUT buttons has no effect.

The increasing popularity of portable computer systems such as notebooks and 

laptop computers has prompted consumers to ask for portable and exchangeable 

storage media to give them a certain amount of flexibility. In the late 80’s a 

consortium of manufacturers developed a design, connection and software 

standard for memory cards called PCMCIA (Personal Computer Memory Card 

International Association). PCMCIA cards have also become the media of choice 

in audio engineering, allowing the user to store data externally via PCMCIA card 

slots. Today, the cards are usually referred to as PC cards. 
Your ULTRADRIVE PRO DCX2496 has a PCMCIA card slot on the front panel, 

allowing you to store your presets easily, without having to use the internal 

memory of the device. Use the RECALL menu to recall previously stored presets 

(see chapter 4.8)—from the card or from the internal memory.

Fig. 4.44: Recall ➠ Internal/Card

In the upper display line, the parameter CURRENT NR indicates the current 

preset. If the preset has been edited but not yet stored, an arrow plus “EDITED” 

appears below this line. Now, if you try to load a new preset, the unit warns you 

that the current preset has not been saved yet. If you continue to load a new 

preset, all settings will be lost. 

Fig. 4.45: Recall ➠ Internal/Card

If you wish to store the current preset before loading a new one, cancel RECALL 

and change to the STORE menu (see chapter 4.8).
The parameter RECALL NR allows you to select the BANK, from which to load 

a preset (INT or CARD) and the NUMBER of the preset. Both values are shown 

in the large right-hand window Use the data wheel to select a preset (1 - 60). 

Confirm your selection with OK to return to the previously selected menu 

(before entering RECALL).

Use this menu to  store previously created presets in the internal memory or on a 

PCMCIA card.