JVC DT-V9L5 Manuel D’Utilisation

37

37

 

Setting values: Off, On

Setting of the function for turning the unit off (standby) automatically when no operations are made for more than 4 hours.

Off: Does not turn off automatically
On: Turns off automatically

●

 When the function is turned On, a warning message will be displayed about 3 minutes before turning off automatically.

When you turn on the unit with the function turned On, a message notifying that the setting is turned on will be displayed for about 30 
seconds.

 Settings for the sub menu display, color of the tally lamp, and the intensity of the button lamps.

Select the contents and displaying position of “sub menu.”

Lower1, Upper1, Lower2, 
Upper2

Displays the current setting and adjustment bar at the lower part of the screen.

Displays the current setting and adjustment bar at the upper part of the screen.

Displays the current setting at the lower part of the screen.

Displays the current setting at the upper part of the screen.

•  The adjustment bar is not displayed for some items.

Set the color and mode of the tally lamp using external control.

:
:

Light up the entire tally.
Light up the left and right halves of the tally individually.

Normal, Half

Set the tally color when “Tally Type” is set to “Normal”.

Green, Red

Back Tally Enable *

1

Select whether to use back tally lamp.

Off, On

Select the intensity of the button lamps.

Normal, Dark

Deactivates the function of PHASE adjustment (Picture adjustment knob and “Picture Sub 
Adjust” in Set-Up Menu) except when an NTSC signal comes in (

☞ on page 38).

Enable, Disable

Set the conditions for the power switch by external control (serial).

Off, On

Cannot power on by external control after powered OFF.
Can power on by external control after powered OFF.

Configure the setting for reducing damage to the LCD panel for long-time use. (

☞ on page 41)

1st Start

Set the standby time. (unit: hours)

00h-24h

Work 
Time

Set the time for performing the function. (unit: hours)

01h-06h

Contrast

Set the contrast reduction.

Normal, Save

Backlight

Reduce the backlight brightness.

Normal, Save

OSD 
Contrast

Set the contrast reduction of the OSD display.

Normal, Save

Side Mask Select whether to use the side mask.

*  The Side Mask function works no matter whether the LCD Saver is active or stopped.

Off, On

reset

Restore the default settings for all the items in “LCD Saver”.

Execute the LCD Saver function.

Stop the LCD Saver function. (“Cancel” will be grayed out during the function stop.)

Display the LCD Saver status. 

Off, Ready

Stop the LCD Saver function. (unit: hours and minutes)

**h **min

Specify the function assigned to the F1 button.

Specify the function assigned to the F1 button.
*   See pages 32 to 40 for details of the functions assigned to Function 1.

- - -, Aperture, I/P Mode, 
Frame, Center Marker, Level 
Meter Display, Gamma, Color 
Temperature, CRC Error, 
Manual Aspect,Time Code, 
1:1, Dynamic, Zebra Mode *

1

, 

Focus Assist Mode *

1

Select whether to display the status of the assigned function when you press the F1 button.

Off, Mode-1, Mode-2

No status display. Perform the registration function.
Display the status. Perform the registration function.
Display the status. Do not perform the registration function.
Perform the registration function when the status is displayed and the button is 
pressed again.

●

  To display the “Function Key Setting” menu, press the   button when the menu is not displayed.

●

  About the operations of F1 button

 

Each time you press the button, the setting value for the assigned function changes in order.

 

Ex: When “Color Temperature” is assigned

 

 

Each time you press the button, three setting values alternate.

*

1

 DT-F9L5 only.

DT-F9L5_EU.indb   37

DT-F9L5_EU.indb   37

2012/12/18   14:13:07

2012/12/18   14:13:07