Omega Vehicle Security DPi8 Fascicule

Step 30. Select the Deviation Control Type Submenu
Press

. If flashing

_DEV Deviation is displayed press

otherwise press

until flashing

_DEV is shown. Now

press

to store and go to next menu item.

Step 31. Select the Latched Type Submenu
Press

. If flashing

UNLT Unlatched is displayed press

otherwise press

until

UNLT is displayed.

Press

to store and advance to next menu item.

Step 32. Select the Normally Open Type of Contact
Closure Submenu
Press

. If flashing

N.o. Normally Open is displayed,

press

, otherwise press

until

N.o. is displayed. Press

to store and advance to next menu item.

Step 33. Select the Above Type of Active Submenu
Press

. If flashing

ABoV Above is displayed, press

otherwise press

until

ABoV is displayed. Press

to store

and advance to next menu item.

Step 34. Enable Alarm 1 at Power On (

A.P.oN)

Press

. If flashing

ENBL is displayed, press

, otherwise

press

until

ENBL is displayed. Press

to store and

advance to next menu item.

Step 35. Enter Alarm 1 High Submenu
Press

twice to skip

ALR.L Alarm 1 Low value. ALR.L is

for below &

ALR.H for above.

Step 36. Set the Alarm 1 High value (

ALR.H)

Press

. Press

until value to set the display to

002.0. Press

to save.

Step 37. Enter the Alarm 2 Menu
The display will show

ALR2 the top menu for Alarm 2.

Repeat steps from 28 to 36 to set for Alarm 2 the same
conditions as for Alarm 1.

Step 38. Configuration of Display Color Selection
Press

until the

COLR Display Color Selection Menu

appears on the Display. Configure

COLR as N.CLR / GRN

(green),

1.CLR / RED (red), 2.CLR / AMBR (amber). Please

refer to the operator’s manual if needed.

Step 39. Run a Test
Press

until reset the controller and return to RUN Mode

to display

075.0 (Ambient Temperature). Now you are

ready to observe temperature as it rises 10°F higher than
displayed. Touch the tip of the Thermocouple to raise the
temperature above the Alarm 2 High value

082.0, and AL2

will turn on, and Display Color will change from Green to
Amber. Continue touching the tip to raise the temperature
above the Alarm 1 High value

087.0 and Display Color will

change from Amber to Red.

Step 11. Enter to the Thermocouple Type Input Submenu
Press

to display flashing, previously selected Thermocouple

type.

Step 12. Scroll through available selection of TC types
Press

to sequence thru flashing Thermocouple types,

(select k -for type "K" CHROMEGA

/ALOMEGA

)

J K T E N DIN J R S B C - TC types
J k t E N dN J

R S b C - Display

Step 13. Store TC type
After you have selected the Thermocouple type press

store your selection, the instrument automatically advances
to the next menu item.

Step 14. Enter to Reading Configuration Menu
The display shows

RDG Reading Configuration, which is the

top menu for 4 submenus: Decimal Point, Degree Units,
Filter Constant and Input/Reading Submenus.

Step 15. Enter to Decimal Point Submenu
Press

to show

DEC Decimal Point.

Step 16. Display the Decimal Point position
Press

again to display the flashing Decimal Point position.

Step 17. Select the Decimal Point position
Press

to select

FFF.F Decimal Point position.

Step 18. Store selected Decimal Point position
By pressing

momentarily the Decimal Point position will

be stored and the instrument will go to the next menu item.

Step 19. Enter to Temperature Unit Submenu
Display shows

TEMP Temperature Unit.

Step 20. Display available Temperature Units
Press

to display the flashing Degree

°F or °C.

Step 21. Scroll through Temperature Units selection
Press

to select

°F Degree.

Step 22. Store the Temperature Unit
Press

to display momentarily that the Degree Unit has

been stored and the instrument will go automatically to the
next menu item.

Step 23. Enter the Filter Constant Submenu
Display shows

FLTR Filter Constant Submenu.

Step 24. Display the Filter Constant Value Submenu
Press

to display the flashing, previously selected Filter

Constant.

Step 25. Scroll through available Filter Constants
Press

to sequence thru Filter Constants

0001, 0002,

0004, 0008, 0016, 0032, 0064 and 0128.

Step 26. Store the Filter Constant
Press

momentarily to store

0004 Filter Constant and the

instrument will automatically go to the next menu item.

Step 27. Enter Alarm 1 Menu
The display will show

ALR1 the top menu for Alarm 1. In the

following steps we are going to enable Alarm 1, Deviation,
Unlatch, Normally Open, Active Above, Enable at power on
and +2°F High Alarm i.e. Process Value > Setpoint 1 Value
+2°F will activate Alarm 1.

Step 28. Enter Alarm 1 Enable/Disable Submenu
Press

to display flashing

DSBL / ENBL.

Step 29. Enable Alarm 1 Submenu
If flashing

ENBL is displayed, press

, if

DSBL is displayed,

press

until

ENBL is displayed, then press

to store and

go to the next menu item.

USA

MADE IN

Servicing North America:

USA:DD

One Omega Drive, P.O. Box 4047

ISO 9001 Certified

Stamford CT 06907-0047

TEL: (203) 359-1660DD

FAX: (203) 359-7700

e-mail: info@omega.com

Canada:: D

976 Bergar

Laval (Quebec) H7L 5A1

TEL: (514) 856-6928DD

FAX: (514) 856-6886

e-mail: info@omega.ca

For immediate technical or application assistance:

USA and Canada:D Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

Customer Service: 1-800-622-2378 / 1-800-622-BEST

Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

Mexico and D

TEL: (001) 203-359-7803D

FAX: (001) 203-359-7807

Latin American:D

e-mail: espanol@omega.com

Servicing Europe:

Benelux::

TEL: +31 20 3472121D

FAX: +31 20 6434643

Toll Free in Benelux: 0800 0993344D

e-mail: sales@omegaeng.nl

Czech Republic:D

Frystatska 184, 733 01 Karviná

TEL: +420 59 6311899DD

FAX: +420 59 6311114

e-mail: info@omegashop.cz

OMEGAnet

On-Line Service

www.omega.com

Internet e-mail

info@omega.com

France:D

TEL: +33 1 61 37 29 00D

FAX: +33 1 30 57 54 27

Toll Free in France: 0800 466 342

e-mail: sales@omega.fr

Germany/Austria:D Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
DD

TEL: +49 7056 9398-0DD

FAX: +49 7056 9398-29

Toll Free in Germany: 0800 639 7678

e-mail: info@omega.de

United Kingdom:D One Omega Drive

ISO 9001 Certified

River Bend Technology Centre

Northbank, Irlam Manchester M44 5BD United Kingdom

TEL: +44 161 777 6611D FAX: +44 161 777 6622

Toll Free in England: 0800 488 488

e-mail: sales@omega.co.uk

MQS3446/0307

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of
one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will
extend the warranty period for four (4) additional years if the warranty card enclosed with each instrument is
returned to OMEGA.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will
issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA,
if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply
to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing,
operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive
corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components which wear are not warranted, including but not limited to
contact points, fuses, and triacs.

OMEGA is  pleased  to  offer  suggestions  on  the  use  of  its  various  products.  However,  OMEGA neither
assumes responsibility for any omissions or errors nor assumes liability for any damages that result from
the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA
warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO
OTHER  WARRANTIES  OR  REPRESENTATIONS  OF  ANY KIND  WHATSOEVER,  EXPRESS  OR  IMPLIED,
EXCEPT  THAT  OF  TITLE,  AND  ALL IMPLIED  WARRANTIES  INCLUDING  ANY WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with
respect  to  this  order,  whether  based  on  contract,  warranty,  negligence,  indemnification,  strict  liability  or
otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event
shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications
or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application,
used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic
WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless
from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS/INQUIRIES

Direct  all  warranty  and  repair  requests/inquiries  to  the  OMEGA Customer  Service  Department.  BEFORE
RETURNING ANY PRODUCT(S)  TO  OMEGA,  PURCHASER  MUST OBTAIN AN AUTHORIZED  RETURN  (AR)
NUMBER  FROM  OMEGA’S  CUSTOMER  SERVICE  DEPARTMENT (IN  ORDER  TO AVOID  PROCESSING
DELAYS).  The  assigned AR  number  should  then  be  marked  on  the  outside  of  the  return  package  and  on  any
correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in
transit.

FOR WARRANTY RETURNS, please have the
following information available BEFORE
contacting OMEGA:
1.

Purchase Order number under which the product
was PURCHASED,

Model and serial number of the product under
warranty, and

Repair instructions and/or specific problems
relative to the product.

FOR NON-WARRANTY REPAIRS, consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA:
1.

Purchase Order number to cover the COST of the
repair,

Model and serial number of product, and

Repair instructions and/or specific problems
relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords
our customers the latest in technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

© Copyright 2007 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without
the prior written consent of OMEGA ENGINEERING, INC.

PATENT AND TRADEMARK NOTICE: This product is covered by one or more of the following patents: U.S. Pat.
No. Des. 336,895; 5,274,577; 6,243,021 / CANADA 2052599; 2052600 / ITALY 1249456; 1250938 / GERMANY DE
41 34398 C2 / SPAIN 2039150; 2048066 / UK Patent No. GB2 249 837; GB2 248 954 / FRANCE BREVET NO. 91
12756. The “Meter Bezel Design” is a trademark of Newport Electronics, Inc. USED UNDER LICENSE. Other U.S.
and International Patents pending or applied for.

This device is marked with the international caution symbol. It is important to read the
Setup Guide before installing or commissioning this device, as the guide contains important
information relating to safety and EMC.

WARNING: These products are not designed for use in, and should not be used for, patient-
connected applications.

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.
OMEGA is constantly pursuing certification of its products to the European New Approach Directives.
OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.

TRADEMARK NOTICE:

omega.com

and

are Trademarks of

OMEGA ENGINEERING, INC.

SPECIFICATION

Accuracy:

+0.5°C temp;
0.03% rdg. process typical

Resolution:

1°/0.1°; 10 µV process

Temperature Stability:

0.04°C/°C RTD;
0.05°C/°C TC @ 25°C (77°F);
50 ppm/°C process

Display:

4-digits, 9-segments LED,
21 mm (0.83") with red, green and
amber programmable colors

Input Types:

Thermocouple, RTD, Analog Voltage
and Current

TC: (ITS 90)

J, K, T, E, R, S, B, C, N, L

RTD: (ITS 68)

100/500/1000 ohm Pt sensor
2-, 3-, or 4-wire; 0.00385 or 0.00392
curve

Voltage:

0 to 100 mV, 0 to 1 V, 0 to 10 Vdc

Current:

0 to 20 mA (4 to 20 mA)

Output 1

†

Relay 250 Vac @ 3 A Resistive Load,
SSR, Pulse

Output 2

†

Relay 250 Vac @ 3 A Resistive Load,
SSR, Pulse

†

Only with -AL Limit Alarm option

Options: Communication

RS-232 / RS-485 or 10BaseT
or

Excitation: 24 Vdc @ 25 mA

EXC. not available for Low Power Option

Line Voltage/Power:

90 - 240 Vac ±10%, 50 - 400 Hz*,
or 110-375 Vdc, 4W for Single Display;
5W for Dual Display

* No CE compliance above 60 Hz

Low Voltage Power Option:

12 - 36 Vdc, 3 W** for Single Display;
20 - 36 Vdc, 4 W** for Dual Display

** Units can be powered safely with 24 Vac

but No Certification for CE/UL are claimed.

Dimensions:

48 H x 96 W x 127 D mm
(1.89 x 3.78 x 5")

Weight:

295 g (0.65 lb)

Approvals:

UL, C-UL, CE per EN 61010-1:2001

DPi8 Temperature & Process Monitor

CNi8-AL, CNi8D-AL

Temperature & Process Limit Alarm