FieldServer FS-8700-105 Manuel D’Utilisation
FS-8700-105_National_Time_and_Signal_FACP Manual
Page 23 of 25
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: support@fieldserver.com
Message
Interpretation and Corrective Action
Type / Sub-Port-Number combination.
The message which follows Message #30, in the error log
will provide a suggestion as to what a suitable Map
Descriptor might look like.
To resolve this problem you must edit the configuration
file, creating a Map Descriptor suitable for the message
whose attributes are printed in the error log. Download the
updated configuration file to the FieldServer and then
reset the FieldServer for the changes to take effect.
Type / Sub-Port-Number combination.
The message which follows Message #30, in the error log
will provide a suggestion as to what a suitable Map
Descriptor might look like.
To resolve this problem you must edit the configuration
file, creating a Map Descriptor suitable for the message
whose attributes are printed in the error log. Download the
updated configuration file to the FieldServer and then
reset the FieldServer for the changes to take effect.
NATS:#31 Err. There are No
MD's for this driver.
MD's for this driver.
This message is the extreme form of message #30.
Resolve it the same way. First though, we suggest that
you review some of the Map Descriptor examples found
in section 4.1.4. Then read the notes for message #30.
Resolve it the same way. First though, we suggest that
you review some of the Map Descriptor examples found
in section 4.1.4. Then read the notes for message #30.
NATS:#32 Err. There are No
MD's for Panel/Node_id=%d
NATS:#33 FYI. Suggestion.
Modify MD=%s
MD's for Panel/Node_id=%d
NATS:#33 FYI. Suggestion.
Modify MD=%s
Read the notes for Message #30.
NATS:#34 Err. Reset Rcvd but
ignored.
ignored.
This message is printed if a reset message was received
but no suitable map descriptors were found and thus no
data was reset.
Read Appendix A.2 for more information.
but no suitable map descriptors were found and thus no
data was reset.
Read Appendix A.2 for more information.
NATS:#35 FYI. Use an array
called <%s> to expose
diagnostic info.
called <%s> to expose
diagnostic info.
This message may be safely ignored. It is printed to
prompt you to read Appendix B.2
prompt you to read Appendix B.2
NATS:#36 Err. String <%s>
rejected. Max Len=8
rejected. Max Len=8
The driver’s default list of recognized Trouble Strings can
be amended by means of configuration. An attempt to
modify the list has failed because no Trouble String can
be more than eight characters. Read Appendix A.1 then
correct the configuration file. Download the modified file
to the FieldServer and reset the FieldServer for your
changes to have effect.
be amended by means of configuration. An attempt to
modify the list has failed because no Trouble String can
be more than eight characters. Read Appendix A.1 then
correct the configuration file. Download the modified file
to the FieldServer and reset the FieldServer for your
changes to have effect.
NATS:#37 FYI. String<%s>
update.
ndx/typ/rst=%d/%d/%d
update.
ndx/typ/rst=%d/%d/%d
Based on the notes in Appendix A.1 the Trouble String
Table has been successfully amended. No corrective
action is required.
Table has been successfully amended. No corrective
action is required.
NATS:#38 Err. No space.
String <%s> rejected.
String <%s> rejected.
The maximum number of Trouble Strings’ is 100. There
is no corrective action you can take other than to review
the exiting list and see if they are all necessary.
is no corrective action you can take other than to review
the exiting list and see if they are all necessary.
NATS:#39 FYI. String<%s>
added. ndx/typ/rst=%d/%d/%d
added. ndx/typ/rst=%d/%d/%d
Based on the notes in Appendix A.1 the Trouble String
Table has been successfully added. No corrective action
is required.
Table has been successfully added. No corrective action
is required.
NATS:#40 Err. Cant set node
Valid Panel / Node_ID’s are whole numbers in the range