Cypress CY7C1347G Manuel D’Utilisation
CY7C1347G
Document #: 38-05516 Rev. *F
Page 6 of 22
Functional Overview
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. Maximum
access delay from the clock rise (t
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. Maximum
access delay from the clock rise (t
CO
) is 2.6 ns (250 MHz device).
The CY7C1347G supports secondary cache in systems using
either a linear or interleaved burst sequence. The linear burst
sequence is suited for processors that use a linear burst
sequence. The burst order is user selectable, and is determined
by sampling the MODE input. Accesses can be initiated with
either the Address Strobe from Processor (ADSP) or the Address
Strobe from Controller (ADSC). Address advancement through
the burst sequence is controlled by the ADV input. A two-bit
on-chip wraparound burst counter captures the first address in a
burst sequence and automatically increments the address for the
rest of the burst access.
either a linear or interleaved burst sequence. The linear burst
sequence is suited for processors that use a linear burst
sequence. The burst order is user selectable, and is determined
by sampling the MODE input. Accesses can be initiated with
either the Address Strobe from Processor (ADSP) or the Address
Strobe from Controller (ADSC). Address advancement through
the burst sequence is controlled by the ADV input. A two-bit
on-chip wraparound burst counter captures the first address in a
burst sequence and automatically increments the address for the
rest of the burst access.
Byte write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BW
(BWE) and Byte Write Select (BW
[A:D]
) inputs. A Global Write
Enable (GW) overrides all byte write inputs and writes data to all
four bytes. All writes are simplified with on-chip synchronous
self-timed write circuitry.
four bytes. All writes are simplified with on-chip synchronous
self-timed write circuitry.
Three synchronous Chip Selects (CE
1
, CE
2
, CE
3
) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE
selection and output tri-state control. ADSP is ignored if CE
1
is
HIGH.
Single Read Accesses
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2)
CE
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2)
CE
1
, CE
2
, CE
3
are all asserted active, and (3) the write signals
(GW, BWE) are all deasserted HIGH. ADSP is ignored if CE
1
is
HIGH. The address presented to the address inputs (A
[16:0]
) is
stored into the address advancement logic and the Address
Register while being presented to the memory core. The corre-
sponding data is allowed to propagate to the input of the Output
Registers. At the rising edge of the next clock the data is allowed
to propagate through the Output Register and onto the data bus
within 2.6 ns (250 MHz device) if OE is active LOW. The only
exception occurs when the SRAM is emerging from a deselected
state to a selected state, its outputs are always tri-stated during
the first cycle of the access. After the first cycle of the access,
the outputs are controlled by the OE signal. Consecutive single
read cycles are supported. After the SRAM is deselected at clock
rise by the chip select and either ADSP or ADSC signals, its
output tri-states immediately.
Register while being presented to the memory core. The corre-
sponding data is allowed to propagate to the input of the Output
Registers. At the rising edge of the next clock the data is allowed
to propagate through the Output Register and onto the data bus
within 2.6 ns (250 MHz device) if OE is active LOW. The only
exception occurs when the SRAM is emerging from a deselected
state to a selected state, its outputs are always tri-stated during
the first cycle of the access. After the first cycle of the access,
the outputs are controlled by the OE signal. Consecutive single
read cycles are supported. After the SRAM is deselected at clock
rise by the chip select and either ADSP or ADSC signals, its
output tri-states immediately.
Single Write Accesses Initiated by ADSP
This access is initiated when both of the following conditions are
satisfied at clock rise: (1) ADSP is asserted LOW, and (2) CE
satisfied at clock rise: (1) ADSP is asserted LOW, and (2) CE
1
,
CE
2
, CE
3
are all asserted active. The address presented to
A
[16:0]
is loaded into the Address Register and the address
advancement logic while being delivered to the RAM core. The
write signals (GW, BWE, and BW
write signals (GW, BWE, and BW
[A:D]
) and ADV inputs are
ignored during this first cycle.
ADSP-triggered write accesses require two clock cycles to
complete. If GW is asserted LOW on the second clock rise, the
data presented to the DQs and DQPs inputs is written into the
corresponding address location in the RAM core. If GW is HIGH,
then the write operation is controlled by BWE and BW
complete. If GW is asserted LOW on the second clock rise, the
data presented to the DQs and DQPs inputs is written into the
corresponding address location in the RAM core. If GW is HIGH,
then the write operation is controlled by BWE and BW
[A:D]
signals. The CY7C1347G provides byte write capability that is
on page 8. Asserting the Byte Write Enable
input (BWE) with the selected Byte Write (BW
[A:D]
) input selec-
tively writes to only the desired bytes.
Bytes not selected during a byte write operation remain
unaltered. A synchronous self-timed write mechanism is
provided to simplify the write operations.
unaltered. A synchronous self-timed write mechanism is
provided to simplify the write operations.
Because the CY7C1347G is a common IO device, the Output
Enable (OE) must be deasserted HIGH before presenting data
to the DQs and DQPs inputs. Doing so tri-states the output
drivers. As a safety precaution, DQs and DQPs are automatically
tri-stated whenever a write cycle is detected, regardless of the
state of OE.
Enable (OE) must be deasserted HIGH before presenting data
to the DQs and DQPs inputs. Doing so tri-states the output
drivers. As a safety precaution, DQs and DQPs are automatically
tri-stated whenever a write cycle is detected, regardless of the
state of OE.
Single Write Accesses Initiated by ADSC
ADSC write accesses are initiated when the following conditions
are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted
HIGH, (3) CE
are satisfied: (1) ADSC is asserted LOW, (2) ADSP is deasserted
HIGH, (3) CE
1
, CE
2
, CE
3
are all asserted active, and (4) the
appropriate combination of the write inputs (GW, BWE, and
BW
BW
[A:D]
) are asserted active to conduct a write to the desired
byte(s). ADSC-triggered write accesses require a single clock
cycle to complete. The address presented to A
cycle to complete. The address presented to A
[16:0]
is loaded into
the address register and the address advancement logic while
being delivered to the RAM core. The ADV input is ignored
during this cycle. If a global write is conducted, the data
presented to the DQs and DQPs is written into the corresponding
address location in the RAM core. If a byte write is conducted,
only the selected bytes are written. Bytes not selected during a
byte write operation remain unaltered. A synchronous self-timed
write mechanism has been provided to simplify the write opera-
tions.
being delivered to the RAM core. The ADV input is ignored
during this cycle. If a global write is conducted, the data
presented to the DQs and DQPs is written into the corresponding
address location in the RAM core. If a byte write is conducted,
only the selected bytes are written. Bytes not selected during a
byte write operation remain unaltered. A synchronous self-timed
write mechanism has been provided to simplify the write opera-
tions.
Because the CY7C1347G is a common IO device, the Output
Enable (OE) must be deasserted HIGH before presenting data
to the DQs and DQPs inputs. Doing so tri-states the output
drivers. As a safety precaution, DQs and DQPs are automatically
tri-stated whenever a write cycle is detected, regardless of the
state of OE.
Enable (OE) must be deasserted HIGH before presenting data
to the DQs and DQPs inputs. Doing so tri-states the output
drivers. As a safety precaution, DQs and DQPs are automatically
tri-stated whenever a write cycle is detected, regardless of the
state of OE.
Burst Sequences
The CY7C1347G provides a two-bit wraparound counter, fed by
A
A
[1:0]
, that implements either an interleaved or linear burst
sequence. The interleaved burst sequence is designed
specifically to support Intel Pentium applications. The linear
burst sequence is designed to support processors that follow a
linear burst sequence. The burst sequence is user-selectable
through the MODE input.
specifically to support Intel Pentium applications. The linear
burst sequence is designed to support processors that follow a
linear burst sequence. The burst sequence is user-selectable
through the MODE input.
Asserting ADV LOW at clock rise automatically increments the
burst counter to the next address in the burst sequence. Both
read and write burst operations are supported.
burst counter to the next address in the burst sequence. Both
read and write burst operations are supported.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected before entering the “sleep” mode. CE
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected before entering the “sleep” mode. CE
1
, CE
2
,
CE
3
, ADSP, and ADSC must remain inactive for the duration of
t
ZZREC
after the ZZ input returns LOW.