Sierra Wireless 300 Manuel D’Utilisation
DART 300 Migration Guide
Comparative AT Command Reference
2110291 Rev 1.0
Page 30
Table 4-7: AT [+] Commands (continued)
Command
DART 200
DART 300
+WPRSSI
Mean RSSI
The mean RSSI is available in register
S102
S102
.
RSSI and Channel State
Returns the current Receive Signal Strength
Indication (RSSI), channel state, registration
status, and channel number.
Returns the current Receive Signal Strength
Indication (RSSI), channel state, registration
status, and channel number.
+WPSPNI=
[n[,n[,...n]]]
[n[,n[,...n]]]
Restrict Channel Selection
Uses a combination of the personalization
mode command ^I to set the SPNI value(s)
and \J2 to enable SPNI matching.
mode command ^I to set the SPNI value(s)
and \J2 to enable SPNI matching.
Service Provider Network ID Table Write.
Sets up to 10 SPNI values in decimal,
separated by commas.
Sets up to 10 SPNI values in decimal,
separated by commas.
+WPSPNI?
Subscriber Identity
Supported via the \S? query. The SPNI list
is displayed in addition to the NEI table.
is displayed in addition to the NEI table.
Service Provider Network ID Table Read
Returns the SPNI table.
Returns the SPNI table.
+WS<n>=[x]
WS-register Write
Not supported. The DART 200 uses only
S registers.
S registers.
WS-register Write
Sets the contents of the specified +WS-
register (n) to the new value (x).
Sets the contents of the specified +WS-
register (n) to the new value (x).
+WS<n>?
WS-register Read
Not supported. The DART 200 uses only
S registers.
S registers.
WS-register Read
The contents of the specified +WS-register
(n) are returned to the host (DTE) as ASCII
decimal digits.
The contents of the specified +WS-register
(n) are returned to the host (DTE) as ASCII
decimal digits.
+WVCALLERIP
Caller IP
Supported via the S53 register. This also
includes the port number.
Supported via the S53 register. This also
includes the port number.
Caller IP
Reports the IP address of the currently
connected remote terminal. The port number
is not included.
Reports the IP address of the currently
connected remote terminal. The port number
is not included.
+WVFRIEND=
Friends Only
Uses the dial directory entered via &Z.
Checking is enabled with S82=1.
Checking is enabled with S82=1.
Active Friend Write
This writes the specified IP address and
optional port to the table entry indexed by
+WS213
This writes the specified IP address and
optional port to the table entry indexed by
+WS213
(Active Friend List Index).
+WVFRIEND?
Active Friend Read
The dial directory used for friend list
matching is displayed using &Z?.
matching is displayed using &Z?.
Active Friend Read
Returns the IP address and port, in dotted IP
format, of the Friend List table entry as
determined by the index in +WS213 (Active
Friend List Index).
Returns the IP address and port, in dotted IP
format, of the Friend List table entry as
determined by the index in +WS213 (Active
Friend List Index).
+WVFRIENDLIST
Active Friend Read
The dial directory used for friend list
matching is displayed using &Z?.
matching is displayed using &Z?.
Friend List
Displays the current ten-entry Friend List
table.
Displays the current ten-entry Friend List
table.
+WVRESET
Reboot
Supported using the –R command.
Supported using the –R command.
Soft Modem Reset
Resets the modem to power-up condition.
Resets the modem to power-up condition.