Technics MT5634SMI-92 Manuel D’Utilisation
Appendix B – Product Approvals, Design Considerations, Regulatory Information
SocketModem Global MT5634SMI Developer’s Guide
85
FCC Part 68 Telecom
1.
This equipment complies with part 68 of the Federal Communications Commission Rules. On the outside
surface of this equipment is a label that contains, among other information, the FCC registration number.
This information must be provided to the telephone company.
surface of this equipment is a label that contains, among other information, the FCC registration number.
This information must be provided to the telephone company.
2.
The suitable USOC jack (Universal Service Order Code connecting arrangement) for this equipment is
shown below. If applicable, the facility interface codes (FIC) and service order codes (SOC) are shown.
shown below. If applicable, the facility interface codes (FIC) and service order codes (SOC) are shown.
3.
An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment is
designed to be connected to the telephone network or premises wiring using a compatible modular jack that
is Part 68 compliant.
designed to be connected to the telephone network or premises wiring using a compatible modular jack that
is Part 68 compliant.
4.
The ringer equivalence number (REN) is used to determine the number of devices that may be connected to
the telephone line. Excessive RENs on the telephone line may result in the device not ringing in response to
an incoming call. In most, but not all, areas the sum of the RENs should not exceed 5.0. To be certain of the
number of devices that may be connected to the line, as determined by the total RENs, contact the local
telephone company.
the telephone line. Excessive RENs on the telephone line may result in the device not ringing in response to
an incoming call. In most, but not all, areas the sum of the RENs should not exceed 5.0. To be certain of the
number of devices that may be connected to the line, as determined by the total RENs, contact the local
telephone company.
5.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance
that temporary discontinuance of service may be required. But if advance notice is not practical, the
telephone company will notify you as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
that temporary discontinuance of service may be required. But if advance notice is not practical, the
telephone company will notify you as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
6.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could
affect the operation of the equipment. If this happens, the telephone company will provide advance notice in
order for you to make necessary modifications in order to maintain uninterrupted service.
affect the operation of the equipment. If this happens, the telephone company will provide advance notice in
order for you to make necessary modifications in order to maintain uninterrupted service.
7.
If trouble is experienced with this equipment (the model of which is indicated below) please contact Multi-
Tech Systems, Inc. at the address shown below for details of how to have repairs made. If the trouble is
causing harm to the telephone network, the telephone company may request you remove the equipment
from the network until the problem is resolved.
Tech Systems, Inc. at the address shown below for details of how to have repairs made. If the trouble is
causing harm to the telephone network, the telephone company may request you remove the equipment
from the network until the problem is resolved.
8.
No repairs are to be made by you. Repairs are to be made only by Multi-Tech Systems or its licensees.
Unauthorized repairs void registration and warranty.
Unauthorized repairs void registration and warranty.
9.
This equipment should not be used on party lines or coin lines.
10.
If so required, this equipment is hearing aid compatible.
Manufacturer:
Manufacturer:
Multi-Tech Systems, Inc.
Trade Name
SocketModem
Model Number:
MT5634SMI
FCC Registration No:
AU7-USA-25814-M5-E
Ringer Equivalence:
0.3B
Modular Jack (USOC):
RJ11C or RJ11W (single line)
Service Center in USA:
Multi-Tech Systems, Inc.
2205 Woodale Drive
Mounds View, MN 55112
U.S.A.
(763) 785-3500
(763) 785-9874 Fax
2205 Woodale Drive
Mounds View, MN 55112
U.S.A.
(763) 785-3500
(763) 785-9874 Fax
Telecom Labeling Requirements
FCC regulations require labeling of registered Telephone and Data Terminal Equipment in accordance with Part 68
Subpart D. There are two options available for labeling of the device containing the MT5634SMI SocketModem.
The first option would be to use the registration number assigned to Multi-Tech Systems, Inc. by the FCC as
explained in Section 68.300 below and shown in the sample label. The second option would be for the customer to
submit applications for and use their own registration number that would be assigned by the FCC. This would
require a letter of authorization for reregistration written by Multi-Tech Systems, Inc. giving the customer permission
to reregister the product. The customer would also need to obtain and file the necessary documents and pay the
required fees to the FCC.
Subpart D. There are two options available for labeling of the device containing the MT5634SMI SocketModem.
The first option would be to use the registration number assigned to Multi-Tech Systems, Inc. by the FCC as
explained in Section 68.300 below and shown in the sample label. The second option would be for the customer to
submit applications for and use their own registration number that would be assigned by the FCC. This would
require a letter of authorization for reregistration written by Multi-Tech Systems, Inc. giving the customer permission
to reregister the product. The customer would also need to obtain and file the necessary documents and pay the
required fees to the FCC.
Similarly, Industry Canada requires labeling in accordance with CS-03 requirements. An Industry Canada label
should be attached to the final product as described in the Industry Canada CS-03 section below. A label can be
purchased from Multi-Tech or a label printing company available to you. A Multiple Listing (similar to FCC’s re-
registration) is also an option for Industry Canada labeling.
should be attached to the final product as described in the Industry Canada CS-03 section below. A label can be
purchased from Multi-Tech or a label printing company available to you. A Multiple Listing (similar to FCC’s re-
registration) is also an option for Industry Canada labeling.