Panasonic CF-W5 Manuel D’Utilisation
30
G
ett
in
g S
ta
rte
d
U
se
ful
In
formati
on
Trouble
s
hooting
Appendi
x
Hardware Diagnostics
Disconnect any peripheral devices before running the diagnostic check.
1
Connect the AC adaptor, and turn on the wireless switch.
During the diagnostic check, do not remove the AC adaptor, or attach any peripheral devices.
2
Turn on or restart the computer, and press
F2
while [Panasonic] boot screen is displayed.
The Setup Utility starts up.
z
z
If you are using the computer after changing the settings from the status at the time of purchase, we recom-
mend that you make a note of the settings that are changed.
mend that you make a note of the settings that are changed.
3
Press
F9
.
At the confirmation message, select [Yes] and press Enter.
4
Press
F10
.
At the confirmation message, select [Yes] and press Enter.
The computer will restart.
The computer will restart.
5
Press
Ctrl
+
F7
while [Panasonic] boot screen is displayed.
When the PC-Diagnostic Utility starts up, it will automatically begin the diagnostic check for all hardware components.
z
z
The touch pad and the internal keyboard cannot be used until alternating blue and yellow colors are displayed
on the left side of the hardware icon (Î page 29). If the touch pad does not operate properly, press Ctrl +
on the left side of the hardware icon (Î page 29). If the touch pad does not operate properly, press Ctrl +
Alt + Del to restart the computer, or slide the power switch to turn the power off, and then restart the PC-Diag-
nostic Utility.
nostic Utility.
NOTE
z
Using the following procedure, you can run a diagnostic check on a specified hardware component,
or run an extended diagnostic check on the hard disk.
or run an extended diagnostic check on the hard disk.
A
Click
to stop the diagnostic check.
B
Click the icon for the hardware that is not to be checked, so that the icon is displayed in gray (B).
When running a check on the hard disk, clicking the icon once will turn on the extended diagnostic
check (“FULL” (C) will be displayed below the icon); click again, and the icon will be displayed in
gray.
When running a check on the hard disk, clicking the icon once will turn on the extended diagnostic
check (“FULL” (C) will be displayed below the icon); click again, and the icon will be displayed in
gray.
C
Click
to start the diagnostic check.
6
When all the hardware has been checked, confirm the diagnostic check results.
If the display is red and the message “Check Result TEST FAILED” is displayed, you can assume that there is a
problem with the computer’s hardware. Confirm which hardware component is displayed as red, and contact your
technical support office.
If the display is green and the message “Check Result TEST PASSED” is displayed, the computer’s hardware is
operating normally. Continue using the computer as it is. If the computer still does not operate properly, reinstall
the software. (Î page 23)
problem with the computer’s hardware. Confirm which hardware component is displayed as red, and contact your
technical support office.
If the display is green and the message “Check Result TEST PASSED” is displayed, the computer’s hardware is
operating normally. Continue using the computer as it is. If the computer still does not operate properly, reinstall
the software. (Î page 23)
NOTE
z
If you run a memory diagnostic check after installing a new RAM module (sold separately) and the message “Check
Result TEST FAILED” is displayed:
Remove the additional RAM module and run the diagnostic check again. If the message “Check Result TEST
FAILED” is still displayed, you can assume that there is a problem with the internal RAM module.
Result TEST FAILED” is displayed:
Remove the additional RAM module and run the diagnostic check again. If the message “Check Result TEST
FAILED” is still displayed, you can assume that there is a problem with the internal RAM module.
7
After the diagnostic check is complete, click
(close), or press
Ctrl
+
Alt
+
Del
to
restart the computer.
Running the Diagnostic Check
C
CF-W5mk2-PCSC.book 30 ページ ２００６年１０月２日 月曜日 午後１時１２分