ATTO Technology SC 5700 Manuel D’Utilisation
3
ATTO Technology Inc. FastStream SC Installation and Operation Manual
1.1 FastStream SC 5300 Physical Attributes
The ATTO FastStream SC 5300 is a Fibre Channel to SCSI storage appliance which can be seamlessly
integrated into a new or an existing storage environment.
integrated into a new or an existing storage environment.
The ATTO FastStream SC 5300 is available in a
desktop model and in an industry-standard 1U form
factor for easy integration into racks.
For installation instructions, refer to
desktop model and in an industry-standard 1U form
factor for easy integration into racks.
For installation instructions, refer to
Dimensions
Width: 17 inches
Length: 8.94 inches
Height: 1.7 inches (1U)
Weight: approximately 8 pounds
Length: 8.94 inches
Height: 1.7 inches (1U)
Weight: approximately 8 pounds
Cooling and airflow
Operating Temperature: 0°-40° C external
Humidity: 10-90% non-condensing
Airflow: air enters through slots on the right of the
rear panel and exits through slots on the left of the rear
panel.
Humidity: 10-90% non-condensing
Airflow: air enters through slots on the right of the
rear panel and exits through slots on the left of the rear
panel.
CAUTION
CAUTION
Do not block the enclosure’s vents. The
FastStream does not allow data transfer if
overheating occurs.
FastStream does not allow data transfer if
overheating occurs.
Power
The power supply circuit is permanently mounted
within the enclosure and is not hot-swappable. It has
one standard IEC320 power receptacle and switch.
within the enclosure and is not hot-swappable. It has
one standard IEC320 power receptacle and switch.
WARNING
WARNING
Risk of explosion if battery is removed
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
and/or replaced by an incorrect type.
Dispose of used batteries in accordance
with your local environmental regulations.
Explosionsgefahr, wenn die Batterie falsch
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
entfernt und/oder ersetzt wird. Entsorgen
Sie benutzte Batterien in Übereinstimmung
mit Ihren lokalen
Umweltschutzbestimmungen.
Input voltage: 10/230V AC, with operating input
range of 90-132V AC or 175-264V AC, 47-63Hz,
single phase. The AC input range selection is
range of 90-132V AC or 175-264V AC, 47-63Hz,
single phase. The AC input range selection is
automatic with no manual or jumper switchover
required.
Power draw: 2 amps at 110V, 1.6 amps @ 90V
required.
Power draw: 2 amps at 110V, 1.6 amps @ 90V
Fibre Channel ports
Two independent 4-Gigabit Fibre Channel ports
connect the FastStream using Small Formfactor
Pluggable (SFP) interfaces and multimode fiber optic
cable.
connect the FastStream using Small Formfactor
Pluggable (SFP) interfaces and multimode fiber optic
cable.
SCSI ports
The two SCSI ports are totally independent from each
other.
The ports are Ultra 320 SCSI busses with VHDCI
connector, downward compatible with all forms of
Single-ended Differential SCSI and all previous SCSI
protocols.For details on cabling SCSI ports, refer to
other.
The ports are Ultra 320 SCSI busses with VHDCI
connector, downward compatible with all forms of
Single-ended Differential SCSI and all previous SCSI
protocols.For details on cabling SCSI ports, refer to
Management ports
The 10/100 base T Ethernet port is accessible from
the RJ45 connector and supports local diagnostics.
The RS-232 serial port provides
support for remote monitoring
and management using a DB9
connector. The baud rate is
programmable and preset at the
factory to 115200 bps.
the RJ45 connector and supports local diagnostics.
The RS-232 serial port provides
support for remote monitoring
and management using a DB9
connector. The baud rate is
programmable and preset at the
factory to 115200 bps.
LED indicators
The LED indicators can be viewed from the connector
side and the front side of the FastStream SC 5300.
(See
side and the front side of the FastStream SC 5300.
(See
.)
LEDs on the connector side are:
A bicolor Ready/Fault LED lights green to indicate
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
Embedded in the Ethernet port connector: a
lighted green LED shows a valid link; off indicates that
no link is present. A separate blinking yellow LED
indicates activity.
Fibre Channel ports: A lighted green LED indicates
link; off means no link. A separate green LED indicates
activity if it is lit, no activity if it is off.
A bicolor Ready/Fault LED lights green to indicate
ready, lights yellow to show a faulted condition, and is
off to indicate not ready.
Embedded in the Ethernet port connector: a
lighted green LED shows a valid link; off indicates that
no link is present. A separate blinking yellow LED
indicates activity.
Fibre Channel ports: A lighted green LED indicates
link; off means no link. A separate green LED indicates
activity if it is lit, no activity if it is off.
1
9
8
7
6
5
4
3
2
RX
TX
GND