Eicon Networks DM/V600A-2E1-PCI Fascicule

 

Part Number 64-0074-02 

Copyright © 2001-2007 

Dialogic Corporation.    

All rights reserved. 

 

 

CAUTION:  All computer boards are sensitive to 
electrostatic discharge (“ESD”).  Handle all static-
sensitive boards and components at a static-safe work 
area, and observe anti-static precautions at all times. 

 
If you are not familiar with ESD safety precautions, visit 

 

Unpack the Dialogic

®

 DM/V600A-2E1-PCI Media Board 

(“board”) according to the following steps: 

1.  Prepare a static-safeguarded work area. 
2.  Carefully remove the board from the shipping 

carton and anti-static packaging.  Handle the 
board by the edges and avoid touching the 
board’s components. 

3.  Lay the board on the static-dissipative work 

surface. 

Note: Place boards in static-shielding bags when 
carrying boards from station to station. 

 

CAUTION: Do not remove the board from the anti-static 
packaging until you are ready to install it.  Observe 
proper anti-static precautions at all times. 

 

The device driver, part of the system software, assigns 
board instance numbers in ascending order (beginning 
with 0) as it detects each board in your system. A board 
instance number is the identification (ID) number used by 
the system software to recognize the board. 

Note:  If you add or remove a board, the system may 
change the existing board instance numbers, depending 
upon the PCI bus and slot number where the board is 
installed or removed. 

Leave SW1 set to the factory default of 0 to let the 
system automatically assign board instance numbers by 
PCI bus slot number. 

After the hardware and the system software are installed, 
refer to the Dialogic

®

 Configuration Manager (DCM) 

utility to retrieve the assigned board instance ID 
number(s). For more information about board 
identification, see the DCM online help. 

In a Linux system, you must set SW1 to a unique 
number for each installed board. Use a non-magnetic 
screwdriver to turn SW1 to one of 16 board ID settings, 
0–9 or A–F. 

After the hardware and the system software are installed, 
refer to the proper configuration files to retrieve the 
assigned board instance ID number(s). For more 
information about Linux configuration files, see the 
Dialogic

®

 System Software documentation. 

 

1.  With your computer on the static-safe work area, 

switch off the power and disconnect all power cords 
from the electrical outlets. 

2.  Remove the computer cover. 

3.  Select an empty PCI expansion bus slot and remove 

the slot’s retaining screw and access cover plate (if 
applicable). 

4.  If you are not installing your board in an ISA form 

factor PCI slot, remove the ISA edge retainer. 

1.  RJ-48C jacks: Connectors to external 

digital telephone network interface. 

2.  General Network Interface Alarm LED 
3.  Power LED 
4.  Reset LED 
5.  SW1: Rotary switch to set board 

identification (Linux systems only). 

6.  Alarm LEDs: During power-up, indicate 

Power on Self Test (POST) status. During 
operation CH1 and CH2 LEDs indicate 
network alarms for each trunk. 
Red—Alarm to indicate loss of signal 
Yellow—Alarm to indicate loss of frame 
synchronization at far end of external 
network 
Green—Indicates signal present; powered 
up and receiving signal from external E1 
sources 
Loopback—Indicates loopback mode is 
activated 

7.  CT Bus/MVIP Bus Termination Jumpers: 

Bus signal is terminated when the 
corresponding jumper clip is installed. 
Note: Signal must be terminated only on 
boards at each end of the CT Bus cable. 
JP2A—CT Bus termination jumper 
JP2B—MVIP Bus termination jumper 

8.  P3: CT Bus connector 

9.  ISA Edge Retainer 

 

1

2

 

10.Signal Processing Daughterboard