Multi-Tech Systems MT5634ZLXI Manuel D’Utilisation
Chapter 4 – AT Commands, S-Registers, and Result Codes
MT5634ZLX, MT5634ZLXI, MT5634ZLX/FE User Guide
24
Result Codes
Result Codes
Result Codes
Result Codes
In Command mode, the MultiMobile PC Card can send information and status responses (Result Codes)
to your computer. Result Codes are used by communications programs and can also appear on your
monitor. The form of the Result Code information displayed can be defined using the Qn, Vn, Wn, and Xn
commands.
to your computer. Result Codes are used by communications programs and can also appear on your
monitor. The form of the Result Code information displayed can be defined using the Qn, Vn, Wn, and Xn
commands.
Terse Verbose Description
0
OK
Command executed
1
CONNECT
Modem connected to line
2
RING
Ring signal detected
3
NO CARRIER
Carrier signal lost or not detected
4
ERROR
Invalid command
5
*
CONNECT 1200
Connected at 1200 bps
6
NO DIALTONE
No dial tone detected
7
BUSY
Busy signal detected
8
NO ANSWER
No answer at remote end
10 *
CONNECT 2400
Connected at 2400 bps
11 *
CONNECT 4800
Connected at 4800 bps
12 *
CONNECT 9600
Connected at 9600 bps
13 *
CONNECT 14400
Connected at 14400 bps
14 *
CONNECT 19200
Connected at 19200 bps
24 *
CONNECT 7200
Connected at 7200 bps
25 *
CONNECT 12000
Connected at 12000 bps
26 *
CONNECT 16800
Connected at 16800 bps
40 *
CONNECT 300
Connected at 300 bps
55 *
CONNECT 21600
Connected at 21600 bps
56 *
CONNECT 24000
Connected at 24000 bps
57 *
CONNECT 26400
Connected at 26400 bps
58 *
CONNECT 28800
Connected at 28800 bps
59 *
CONNECT 31200
Connected at 31200 bps
60 *
CONNECT 33600
Connected at 33600 bps
70 *
CONNECT 32000
Connected at 32000 bps
71 *
CONNECT 34000
Connected at 34000 bps
72 *
CONNECT 36000
Connected at 36000 bps
73 *
CONNECT 38000
Connected at 38000 bps
74 *
CONNECT 40000
Connected at 40000 bps
75 *
CONNECT 42000
Connected at 42000 bps
76 *
CONNECT 44000
Connected at 44000 bps
77 *
CONNECT 46000
Connected at 46000 bps
78 *
CONNECT 48000
Connected at 48000 bps
79 *
CONNECT 50000
Connected at 50000 bps
* EC is added to these Result Codes when the extended Result Codes configuration option is enabled. EC is replaced
by one of the following codes, depending on the type of error control connection: V42bis (V.42 error control [LAP-M]
and V.42bis data compression); V42 (V.42 error control [LAP-M] only); MNP5 (MNP 4 error control and MNP 5 data
compression); MNP4 (MNP 4 error control only); NoEC (No error control protocol).
by one of the following codes, depending on the type of error control connection: V42bis (V.42 error control [LAP-M]
and V.42bis data compression); V42 (V.42 error control [LAP-M] only); MNP5 (MNP 4 error control and MNP 5 data
compression); MNP4 (MNP 4 error control only); NoEC (No error control protocol).