MicroNet Technology SP5052 Manuel D’Utilisation
27
-idto
The duration of two pressed digits in dial mode
-eod
Digit type of end of dialing. ( 0:No end of dialing, 1:[*]
button,
2:[#] button )
-seizure
Choose line seizure mode (None/UCD).
-2nddial
Config GW to accept 2nd dtmf set. In this mode, device
from IP side needs to dial GW's E164, wait for PSTN
dialtone,
and
then
dial
out.
-drule
Specify digits to be filtered/dropped/inserted before
making an outgoing IP call or after receving an incoming
IP call.
IP call.
-askpin
PIN code prompt before greeting.
0:Disable 1:Per Unit 2:Per Channel.
0:Disable 1:Per Unit 2:Per Channel.
-ring
Ring number before answer.
0:Disable, other is number of ring ( 1 ~ 5 ).
-callalive
Enable or disable auto-disconnection after 10 seconds
-keypad
DTMF setting: 0=In-band, 1=H.245 Alphanumeric,
2=H.245 SignalType, 3=Q.931 UserInfo. , 4=RFC2833.
2=H.245 SignalType, 3=Q.931 UserInfo. , 4=RFC2833.
-pincode
Specify 6 of PIN codes.
-sendxcode Send access code after connection.
0:Disable 1:Enable.
-access
Specify access codes.
Note:
Use character 'x' to delete the drule parameter.
For line seizure 0: None, 1: UCD.
For askpin: f=0: No, f=1: Yes.
Direct in line feature should be used together with:
For line seizure 0: None, 1: UCD.
For askpin: f=0: No, f=1: Yes.
Direct in line feature should be used together with:
$sysconf –2nddial 0 (2nddila off)
$h323 –mode 0 (Gatekeeper mode)
$bureau –print
$h323 –mode 0 (Gatekeeper mode)
$bureau –print
for Direct in line table configuration
Hotline feature should be used together with:
$sysconf -2nddial 0 (2nddial off)
$h323 -mode 1 (peer-to-peer mode)
$bureau -print for Hotline/LineToLine table configuration.
LineToLine feature should be used together with:
$sysconf -2nddial 1 (2nddial on)
$h323 -mode 1 (peer-to-peer mode)
$bureau -print for Hotline/LineToLine table configuration.
$h323 -mode 1 (peer-to-peer mode)
$bureau -print for Hotline/LineToLine table configuration.
Example:
sysconf -service 0 -plan 4 -port 1 1 1 1 0 0
sysconf -callalive 0 -keypad 0
sysconf -2nddial 0 -drule out_filter 002 in_insert x in_drop 1
sysconf -askpin 1 -pincode set1 12345
sysconf -sendxcode 1 -access set1 12345#
sysconf -callalive 0 -keypad 0
sysconf -2nddial 0 -drule out_filter 002 in_insert x in_drop 1
sysconf -askpin 1 -pincode set1 12345
sysconf -sendxcode 1 -access set1 12345#
- service
0 (Dial In Service): In Dial In Service, VoIP FXO gateway will
pick up incoming calls from PSTN, play pre-recorded voice
greeting or, and then have users to make a 2nd dial to
destination.
pick up incoming calls from PSTN, play pre-recorded voice
greeting or, and then have users to make a 2nd dial to
destination.