GE GFK-0787B Manuel D’Utilisation

tModular Redundancy Flexible Triple Modular Redundant (TMR) System 

The following tables lists PLC Fault Table messages for GMR.. If you need additional
help, call GE Fanuc Technical Service  at  1–800–828–5747.

100

No CPU Clock

There is no PLC clock present

100

No PLC Clock

There is no PLC clock present

101

Illegal state step

Internal GMR error: invalid step

101

Illegal trans code

Internal GMR error: invalid transition code

101

Bad trans x from wwww

Internal GMR error: attempted transition to invalid step

100+
GBC ID

CFPT, 0 attempts wwww

Number of attempts exhausted while trying to send a COMREQ

10009

GMRx ornge GBC g req

Out of range Bus Controller (g) was requested by GMRx module

10009

GMRx bad GBC g req

Unconfigured Bus Controller (g) was requested by GMRx module

10010

GMRx ornge GBC g rel

Out of range Bus Controller (g) was released by the GMRx module

10010

GMRx bad GBC g rel

Unconfigured Bus Controller (g) was released by the GMRx module

10011

GMRx ornge GBC g flt

Out of Range Bus Controller (g) was faulted by the GMRx module

10011

GMRx bad GBC g flt

Unconfigured Bus Controller (s) was faulted by the GMRx module

1

Unauthorized GMR Access

Initialization module was invoked with incorrect password

10102

Incorrect GMR Version

Initialization module was called with incorrect version number

10103

GMR Software Exception

An invalid call number was detected

10104

Invalid GMR Pointer

Initialization module was invoked with invalid pointer for diagnostics area

10109

Prog Checksum Timeout

PLC didn’t calculate the program checksum within 10 seconds

10110

Invalid Bus Address

Initialization detected bus addresses not equal to 29, 30, or 31

10111

Sync Not Possible

Synchronization cannot be performed

10112

Output discrepancy

Output discrepancy detected

10113

Miscomp, no more retries

Sync detected miscompare

10114

GMR Coldstart

GMR is performing coldstart

10115

GMR Warmstart

GMR is performing a warmstart

10116

Cannot get all GBCs

Cannot acquire all GBCs during initialization

10117

Cannot do VME Write

The VME Write to 7F3h was unsuccessful

10119

Invalid Switch Case

An invalid case condition was detected during a switch

10120

Failed Disable Ops

The Disable Outputs command (COMREQ) failed to complete successfully

10121

Failed Enable Ops

The Enable Outputs command (COMREQ) failed to complete successfully

10122

Failed Set GMR Mode

The Set GMR Mode command (COMREQ) failed to complete successfully

10123

Failed DG Dgrams

The Clear Datagrams Dequeue command (COMREQ) failed to complete successfully

10124

Failed Read Address

The Read Bus Address command (COMREQ) failed to complete successfully

10129

Num dequeues = n

N dequeue entries were dequeued at startup

10130

Program mismatch A/B

PLCs A and B program mismatch, C is not online

10131

Program mismatch B/C

PLCs B and C program mismatch, A is not online

10132

Program mismatch A/C

PLCs A and C program mismatch, B is not online

10133

Program mismatch A/B&C

PLC A program mismatch with B and C

10134

Program mismatch B/A&C

PLC B program mismatch with A and C

10135

Program mismatch C/A&B

PLC C program mismatch with A and B

10136

Program mismatch A/B/C

All three PLCs mismatch

10137

Program changed A

PLC A program changed

10138

Program changed B

PLC B program changed

10139

Program changed C

PLC C program changed

10140

Config mismatch A/B

PLCs A&B config mismatch, C not online

10141

Config mismatch B/C

PLCs B and C config mismatch, A is not online

10142

Config mismatch A/C

PLCs A and C config mismatch, B is not online

10143

Config mismatch A/B&C

PLC A config mismatch with B and C

10144

Config mismatch B/A&C

PLC B config mismatch with A and C

10145

Config mismatch C/A&B

PLC C config mismatch with A and B